2. The following resistors are connected in series 470 ohms, 680 ohms, 1 kiloohms and 1.2 kilo ohms. The votage is 20V. The current through the 680 ohms resistor is approximately.. 3. The inductance of an iron core decreases if the number of turns is 4. It is device that stores electric energy, previously called condenser.

2. The following resistors are connected in series 470 ohms, 680 ohms, 1 kiloohms and 1.2 kilo ohms. The votage is 20V. The current through the 680 ohms resistor is approximately.. 3. The inductance of an iron core decreases if the number of turns is 4. It is device that stores electric energy, previously called condenser.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
A good rule-of-thumb to estimate the expected life of a motor, a ballast, or other electrical equipment is that for every ____________ C above rated temperature, the expected life will be cut in __________________.
Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a) Exciting current (ii) Ic (b) Magnetizing Current (iii) Ie (c) core loss current
Nichrome ribbon resistor elements each has a resistance of 1 ohm. The element is made from sheet of nichrome alloy, 0.025cm thick. If the width of the ribbon is 0.3cm, what length is required per element? Assume specific resistance of nichrome allow to be 109micro ohm-cm.
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: i. ratio of mutual to self-capacitance ii. the bus-bar voltage of the substation. iii. Efficiency across the string of insulators
In a 36KV overhead line, there are 3 units in the string of insulators. If the capacitance between each insulator to pin and earth is 55% of self-capacitance of each insulator. Find the distribution of voltage over three insulators and string efficiency.
one turn of a copper bar is produced by cutting copper washer along a radius and spreading the ends. The washer is cut from soft drawn copper having a resistivity at 20 degrees celsiu of 1.732 micro ohm-cm. The washer is 0.125 inch thich and has inside diameter and outside dianmeter of 1 inch and 9 inches respectively. Calculate the exact resistance between the two end of the turn. Assume the contact along the ends of the turn to be perfect over the entire crown section.
6. Show complete and detailed solution.
can you create a diagram of this circuit? resistance:220 ohm diode 1N4007 BC548B Transıstor 1.5 V battery(current source) Capacıtor 470uf 25V shock coil ( I made 15 and 30 wraps to feritte core)(ı do not know the value.)
A. In the morning, the student plugs in a computer (240 W) to study physics, a microwave (800 W) to make breakfast, and a hair dryer (1200 W) to dry the hair. What is the overall current in this student's room, in Ampere? B. A circuit in a student’s room has a 15 A circuit breaker. In the morning, the student plugs in a computer (240 W) to study physics, a microwave (800 W) to make breakfast, and a hair dryer (1200 W) to dry the hair. Will this be enough to trip the circuit breaker? not enough information no, because the overall current is more than 15 A no, because the overall current is less than 15 A yes, because the overall current is less than 15 A yes, because the overall current is more than 15 A
After the determination of the currents references, can we connect the ammeter terminals in any way in order to measure the current of a component? *please write it using keybord NOT handwriting*