6. Calculate the average power delivered to each resistor for the circuit shown below. 50 Ω www 38 Ω www 5 cos 120mt A(+) ww 1.5 Ω · ell 1:9 elle 1:4 9 Ω

Q: 1) - A student connects an ammeter in parallel and notices that the reading is a very large  number.…

A: The ammeter is always connected in series, when the ammeter is connected in parallel, there will be…

Q: Y(S) = 1 1.551x10-5s+1

A:

Q: Problem 3 For two signals x₁ (n) = {2, 1} and x₂ (n) = {-1, 2}, 个 个 a) Calculate 2-point Discrete…

A:

Q: Select the correct answer for each of the following statements Book Source: Electricity 3 | 10th…

A: Generator, A generator is a machine that is used for the conversion of mechanical energy into useful…

Q: 1. For the G(s), make a plot of the log magnitude and the phase, using log-frequency in rad/s as the…

A:

Q: A two-beam interferometer is illuminated with light of irradiance lo, assuming perfect splitting…

A: Given below clear explanation

Q: Consider the discrete-time system shown in Figure Q1 (b). Determine if the system is (i) time…

A: We need to check whether the given system is time invariant and linear.

Q: Given the following system, determine the response of the system, the roots of the system, the…

A:

Q: Find the SAE's for the assigned loop currents. Solve for the loop currents. Round answer to 2…

A: The required mesh current can be calculated by writing the mesh equation using kirchhoff's voltage…

Q: Question-7d, An 8-pole, 50 Hz, three-phase, slip-ring induction motor has an effective rotor…

A: Given- 8-pole, 50 Hz, three-phase, slip-ring induction motor, Effective rotor resistance = 0.08 Ω…

Q: 4. Reduce the network given below to the fewest possible elements by combining the capacitors, and…

A:

Q: find RL and max power transfer to RL

A: It is given that:

Q: Express the voltage v (t) = 5√2 cos(8t) + 2 sin(8t+45") V In the general form v (t) = Acos(wt+0)V…

A:

Q: Explain the function of the input on the FUP FLOP A. SET B. RESET

A: We need to explain the function of inputs given below on the Flip Flop. A) SET(S) B) RESET(R)

Q: =52+ +1 4H 212. 452 m 222 FREE vo(t)=

A:

Q: 1) Please implement following functions using 2-4 decoder f(A,B) = Em(0,3) f(A,B) = Σm(1,2)

A: We need to design the given Boolean function by using of decoder.

Q: 4 cos 5r V ( k₁=0.64 1H 1H: ΣΤΗ IH ky = 0,82 1 + ΤΩ ΖΩ

A: Given data: The given circuit diagram is shown below,

Q: 7) List the similarities and differences between the tone() function and the analogWrite() function.

A: 7. Differences- Depending on the kind of output being used, the analog notation may change.…

Q: Plot the function f(x) 2+ sinx , for -4≤x≤4. please solve using matlab and attach script

A: clc; clear; x=-4:0.01:4; f=(x.^2)./(2+sin(x)+(x.^4)); plot(x,f);

Q: Find the following unknowns given the voltage: v(t) = 440 cos (2513t +195°) V.  a.Average b. Rms…

A: In this question we need to find the average and RMS value of the given voltage equation

Q: What are MEMS drug delivery devices?   Explain different methods of drug delivery using MEMS.…

A: 1) Micro-electromechanical systems (MEMS) is a processing technology used to create tiny or small…

Q: -4. A 30 KW, 250-V, d.c. shunt generator has armature and field resistances of 0.060 and 100…

A:

Q: Find Inverse Laplace Transform through partial fraction expansion. G(s) = (s+4X5+5)* σ>-4

A: In this question We need to determine the inverse Laplace transform of the given signal using the…

Q: 7. When it is necessary to provide automatic control of the voltage output at constant speed, the…

A: Conceptual Background:- DC Generators:- An electrical device called a DC generator's principal job…

Q: ! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: In this question We need to determine the thevenin equivalent and Norton equivalent circuit.  We…

Q: 3. For the motor, load and torque-speed curve, find the transfer function, G(s) = 0L(S)/Ea(s). T…

A:

Q: 2. Determine (a) currents 1₁, 12, 13, and 14 and (b) the voltage across the current source. +12V. 9…

A: We need to find out the current and voltage for given circuit.

Q: * The voltage Vout in the circuit shown is

A: Given data, Circuit diagram is given as,

Q: Question In a single-phase transformer, the total iron loss is 2500 W at nominal voltage of 440 V…

A: Given- A single-phase transformer, Total iron loss P1=2500 W, Voltage V1=440 V, Frequency f1=50 Hz,…

Q: Question a a What is the total capacitance of the combination (C Total) b. What is the total charge…

A: Given data, Circuit diagram is given as,

Q: phase angle

A:

Q: Consider the unity feedback system shown in Figure 2 where R(s) is reference put and Y(s) is system…

A: We need to find out the range of k for stable system .

Q: In a balanced three-phase wye–delta system, the source has an abc-phase sequence and Van = 120angle…

A: In this question We need to determine the load impedance per phase in the delta.  We know Impedance…

Q: Given a truth table in Table Q2, determine the standard SOP expression. Simplify the expression and…

A: We need to find out the Boolean expression for given truth table .

Q: (c) A linear time (shift) invariant system is shown in Figure Q1(c) with q[n], p[n] and r[n]…

A: C) Given  difference equation is r(n) = 4p(n) + 3p(n-1) - 3p(n-2) + 2p(n-3) Where, p(n) is input,…

Q: Variation of critical clearing time with respect to inertia constant H is given below. H( MJ/MVA) 2…

A: Critical clearing angle and Critical clearing time in Transient stability In the case of single…

Q: Find Zea- WW 502 -j52 ㅏ 150 -1001- j5Q Zea 502 ww 22 -152

A:

Q: In the square wave signal in the figure, the duration of 1 is 0.6ms and the period is 1ms; a) What…

A: As per Bartleby guideline we need to answer the first three questions only. Kindly repost the rest…

Q: Recall the equation of the Z-parameters -- V₁ 1 [H = V₂ Z21 Z22 U₁ Determine the Z-parameters (up to…

A: We need to find out the Z parameters for given circuit .

Q: In reference to the given circuit, what is the peak load voltage, Blank 1 if the diode drop is…

A: Given: Primary RMS Voltage = 110Vrms N1 = 10 N2=1 Vd = 0.65V Need to calculate the peak load…

Q: 2. Find the phasors for each of the following signals: ( i(t) = -20 cos(20t +30) v(t) = 30 sin(10t…

A:

Q: Evaluate the DTFS coefficients of x[n] = {… …. … , -1, 0, 1(origin), 0, -1, 0, 1, 0, … …. …}.

A: Given, x[n] = {… …. … , -1, 0, 1(origin), 0, -1, 0, 1, 0, … …. …} We need to evaluate the DTFS…

Q: Question 1 In circuit shown in Figure 1, find a) I(t) and vo for t 0 10V DC 2 ohms M t= 0 Figure 1…

A: We need to find out the current and voltage for given circuit .

Q: expression and draw the logic circuit. the standar 001 010 011 100 Table Q2 INPUTS ABC 000 OUTPUT X…

A: Given,

Q: CREATE A SIMPLE DIAGRAM USING A CONNECTION OF SERIES

A: We need to draw a simple circuit diagram using connection of series.

Q: 10.10 A uniform wave in air has E = 10 cos (2 x 10°t - Bz) ay (a) Calculate 3 and A. (b) Sketch the…

A: We need to analyse the given electric field and we need to find out magnetic field .

Q: Use nodal analysis to solve unknown node voltages in the circuit shown below and use it to solve for…

A: In this question We need to determine the unknown currents as shown the circuit.  Power delivered by…

Q: Q1 Refer to Figure Q1, show all the calculation to find the value for; a) b) c) Total resistance RT…

A: The total resistance can be calculated by using the resistance reduction techniques and then…

Q: 1. Determine the z-transform and ROC for the time signals, (a) and (b). Sketch the ROC, poles, and…

A:

Q: III. Find the current Lby reducing the circuit to the right of terminals a-b to its simplest form…

A: Given: In this question, the given details are, Here, to find the value of the current i by reducing…