2. The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required diameter of the pins at D and C if the allowable shear stress for the material is t =100 MPa. Pin C is subjected to single shear, whereas pin D is subjected to double shear. 15 kN -15m- D. 15 m B. 15m

2. The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required diameter of the pins at D and C if the allowable shear stress for the material is t =100 MPa. Pin C is subjected to single shear, whereas pin D is subjected to double shear. 15 kN -15m- D. 15 m B. 15m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 11P

See similar textbooks

Similar questions

A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
B. Calculate the maximum shear and moment at a point 6m from the left support. Highway uniform load = 100 kN/m; highway point load = 200 kN; uniform dead load = 30 kN/m; point dead load at midspan = 50 kN.
In the cantilever shown, taking M1 = 16 kN-m, M2 = 11 kN-m, P1 = 3 kN, P2 = 7 kN.d) Determine the shear at X2 e) Determine the moment at X2
31 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 2B) 4C) 14D) 0E) 6
The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V to 4H. The purling are supporting a total uniform load of 16 kN/m. Properties of Channel:Sx = 119 x 10^3 mm^3Sy = 87 × 10^3 mm^3 Questions:Compute the maximum bending stress if supported by sagrods at midpoint.
The steel beam has the cross-sectional area shown. if w = 6.5 kips/ft, determine the absolute Horizontal shearing stress (ksi) in the beam Where L1 = 9 ft; L2 = 8 ft; bf = 8.2 in and tw = 0.4 in
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V to 4H. The purling are supporting a total uniform load of 15 kN/m. Properties of Channel:Sx = 119 x 10^3 mm^3Sy = 87 x 10^3 mm^3 Questions:Compute the maximum bending stress if supported by sagrods at third points.
The Channel section is used as a purlin placed on top of trusses with spacing of 4 m and slope 1V to 4H. The purling are supporting a total uniform load of 24 kN/m. Properties of Channel: Sx = 119 x 10^3 mm^3 Sy = 87 x 10^3 mm^3 Compute the maximum bending stress if supported by sagrods at third points. Round your answer to 2 decimal places.
A. Calculate the maximum bending moment and shear at a point 4m from the left support. Highway uniform load = 100 kN/m; highway point load = 200 kN; uniform dead load = 30 kN/m; point dead load at midspan = 50 kN.
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
Determine the vertical and horizontal displace-ments at A of the pin-connected structure in Figure P9.31.Given: E = 200 GPa and A = 500 mm2for all members.