Answered: 1. Draw the shear and bending moment…

1. Draw the shear and bending moment Diagram of the following A) 71kN/m A B |—3 m— 8 m B) 48kN/m 9 m 35 kN A -3m- B -3m- 55 kN-m |--3m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Min kN.m A w in kN/m 3 m B -4 m C

Q: use slope-deflection method to compute the reactions for the following structures 2. 2 m 4 m C ΕΙ…

Q: water resources engineering about? What are its functions and outputs?

A: Water Resources Engineering is a domain of Civil Engineering where the main focus is on the abundant…

Q: Determine the forces in all members using method of joints. 10. E C 5m each H B A 100N vertical…

A: Given,

Q: The truck is moving along a 20 m span of beam. The front axle is 30 kN, the middle is 75 kN and the…

A: Maximum Shear: Taking moment about B ΣMB = 0 R1(20) - 45(20-x) - 75((20-8)-x) - 30((20-8-4)-x) = 0…

Q: Water is pumped thru a vertical 50mm new galvanized-iron pipe to an elevated tank on the roof of a…

Q: the

A: a simple work plan of a weir and label the parts

Q: A vertical wall 6 m high above the water table, retains a 20° soil slope, the retained soil has a…

A: When the soil is…

Q: What is its natural water content (in %)? A soil with a liquidity index of 0.164 has a liquid limit…

A: solution Given liquid limit wL=57%plasticity index IP=39%liquidity index IL=0.164

Q: You are designing a house and would like to calculate the applied loads on the joists (lb/ft). For…

Q: Q.17 In an oedometer test initial depth of the soil sample is 19 mm and the reduction in depth is…

A: given- intial depth of the soil sample=19 mmreduction in depth=2.1 mmfinal void ratio=0.62

Q: Differentiate slip-critical connection and bearing type connection. When is it better to use bolts…

A: The main difference between slip critical connection and bearing type connection is about how they…

Q: Question 2 Compute the area (in acres) of the irregular tracts of land. (All distances are in feet)…

Q: The problem is to be done according to the AISC LRFD Method. All given loads are service loads…

Q: A rural freeway has an ideal free-flow speed of 120 km/hr and two-lanes 3.6 m in each direction,…

Q: Determine the forces in all members using method of joil 9. B 5m D 5 m A 30 kN 5 m 5 m 5 m 20 kN 5 m…

A: To find force in all members of the truss

Q: environmental and energy engineering about and what are its functions and outputs

A: In engineering one can use the scientific principles to design or build structures, machines and…

Q: A house in State College, PA consists of the following: 12 single pane windows (each 10 ft by 1 ft…

Q: Determine the shear and moment as functions of x if x is greater than 4ft but less than 6ft.

Q: 23: Draw shear force and bending moment diagrams by using equation method. 4 kN/m 2 kN/m ·6 mm * -6…

A: GIVEN: TO CALCULATE: Shear force and Bending moment diagram

Q: 23: Draw shear force and bending moment diagrams by using equation method. 4 kN/m 2 kN/m B 6 m 6 m

A: GIVEN: TO CALCULATE: Shear force and Bending moment diagram.

Q: 3) A rural arterial is expected to carry an ESAL of 1.88x10" during the 1st year of operation with…

Q: A scuba tank is being designed for an internal pressure of 2,655 psi with a factor of safety of 2.0…

Q: following data relate to a pump-out test: Diameter of well = 24 cm; Thickness of confined aquifer =…

Q: Give at least 5 examples of jobs where sealant and adhesive can be applied or used.

A: Sealants and adhesives are so confusing at an area of DIY. Some adhesives will seal and some…

Q: A horizontal beam AD with cross-section of 3800 mm² is supported by a wire at C and carries a load…

Q: A concrete beam of rectangular cross-section of size 120 mm x 200 mm is prestressed by a straight…

A: prestressed concrete : The term "prestressed concrete" refers to a type of concrete that is utilized…

Q: For the concrete dam shown below, determine the minimum width in meters of the dam, b, so that it…

Q: If concrete has an idealized compressive stress-strain relationship as shown in Fig.la for the…

Q: If M = 5.41 and w = 26.4, Determine the Shear Force at point B of the Beam shown. w in kN/m Min kN.m…

A: Given data in question Cantilever beam Span member length UDL Concentrated moment To find out…

Q: 15. The following are results of a field unit weight determination test using sand cone method:…

Q: An 8-inch water main carries water (v = 1.41 x 10-5 ft²/s) at a flowrate of 10 ft³/s. The steel pipe…

Q: The beam with cross-section shown carries a uniformly distributed load of intensity w over its…

Q: 2.5m 15kN/m 2.0.m 1 20m Figure 5

Q: a) Write the Shear and Moment Equations of the Beam shown b) Draw the Shear and Moment Diagram…

A: Consider the figure,

Q: The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress.…

Q: What are the functions of construction engineering and management? What are its outputs?

A: Functions Project Management Planning The process of planning out an entire project is the most…

Q: Determine the force in member CD Determine the force in member DG Determine the force in member DH

Q: Group No: Date Performed: Foundation Plan: F1 F2 Rating: Soil Mech Laboratory Plate-03 CONSOLIDATION…

A: Given, Column loadings, F1=F4=F9=F12=4100 kNF2=F3=F10=F11=3800 kNF5=F6=F7=F8=4700 kN Depth of…

Q: Identify if SPONTAENOUS or NON-SPONTAENOUS. a) A ball is being rolled up a slope. b) When exposed…

A: Answer :- Spontaneous are those in which there is no energy applied or it occur by itself . Non…

Q: inertia of rectangular beam

A: Given: For a rectangular channel width w=3 m and depth y=4 m To find: Moment of inertia?

Q: 3m 75 KEN m Im The footing plan is shown loaded uniformly in a rectangular area. What is the value…

Q: For the given properties of the beam below, determine the safest wy that the beam will carry. bf =…

A: fc = 34.5MPa fy = 400MPa

Q: MECHANICS OF MATERIALS Q3: For the beam shown in Figure (5), if the allowable stress at A and B are…

Q: There are two different areas A and B to be trained by means of closed tile drainage KA = 2; LA 2…

A: Given data- k=permeabilitykAkB=2L=spacingLALB=2Q=discharge

Q: 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b.…

Q: A simple beam AB is loaded by two segments of uniform load and two horizontal 900 lb 400 lb 60 lb/ft…

A: Part A solution Let us find the supportt reactions by applying equilibrium of equation FX =0 Ra +…

Q: 1. A baseball pitching machine "throws" baseballs with a horizontal velocity v0. Knowing that height…

Q: 50. What should be the height (m) of a lighthouse, so that it can be visible from a distance of 3…

Q: 5 m A 30 kN B 5 m 5 m 5 m 5 m C 20 kN D 5 m 5 m E

A: method of joints : The method of joints is a method for calculating unknown forces acting on truss…

Question

Direction: USE DIRECT COMPUTATION & COMPLETE SOLUTION

1. Draw the shear and bending moment Diagram of the following
A)
71kN/m
A
B
|——3 m—
8 m
B)
48kN/m
9 m
35 kN
A
-3m-
B
-3m-
55 kN-m
-|---3m-|

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find shear: VA VB VC VD Find Moment: MA MB MC MD Identify Shear Maximum & Moment Maximum
please solve: C1F1 = 13 set
1.What is the maximum intensity of moment for the beam loaded as shown? -20 KN-m -40 KN-m -80 KN-m -72 KN-m 2.What is the shear value at point just before C? 40KN 72KN 80KN 32KN 3.What is the shear value at point just after D? 80KN 72KN 32KN 40KN 4.What is the moment value at B? -72 KN-m -40 KN-m -20 KN-m -80 KN-m 5.What is the value of x, the additional point of zero shear from C? 3.0 m 1.6 m 2.67 m 2.4 m 6.What is the degree of curve in the shear diagram…
To prevent the ladder weighing 600N from sliding down, the man exerts a horizontal force at C. The coefficient of friction at A= 0.2 while surface B is frictionless Find the vertical reaction at Aa. 600N c. 500Nb. 700N d. 800NFind the horizon reaction at Aa. 150N c. 210Nb. 180N d. 120NFind the horizon force exerted by the man at Ca. 533.3N c. 333.3Nb. 667.7N d. 767.6N
Calculate the corrected bearing of line DC.
P1= 100KN A=4
B. In Fig. below; rod AB rotates about an axis through A and s connected t0 block ) by a flexible and inextensible cable. Determine the linear velocity of block 1) when 0 = ' (3/4), and the angular velocity of AB is 2.5 ad/ sec counterclockwise. Fig2B B 15m,
Where: P1=45.5 kN, P2=57 kN, P3=68.5 kN, P4=76kN
Determine the deflection at midspan of the structure Group of answer choices (-5wL^4)/384EI (5wL^4)/384EI (wL^3)/24EI (-wL^3)/24EI
Determine the angle ø (0°≤ø≤90°) between cables BA and BC so that 500N vertical force has a component of 250N which acts along cable CB, from C to B. Set angle = 60°
Determine the slope of the x²+y²-6x-4y-21=0 at (0,7)
A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that it approximately loads the cable by a uniform q(x) = qo. If [= 10 m, ha = 5 m, and he = 4 m, compute the maximum force in the cable for its minimum distance to the ground by 3 m. B y hA hB a (deg) = 16.446 q0 (Kn/m) = 37.632