2. The load per phase of a balanced 30 wye connected load is 8 + j6 Ohms per phase. This is connected to a 30 supply which is 230 cis 0°. Determine the line currents, power factor, P, Q and S of the system.

2. The load per phase of a balanced 30 wye connected load is 8 + j6 Ohms per phase. This is connected to a 30 supply which is 230 cis 0°. Determine the line currents, power factor, P, Q and S of the system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24MCQ: Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line...

See similar textbooks

Related questions

Q: electrical what is the disadvantages of potential transformer ?

A: Potential transformer : The definition of a potential transformer is a device used to transmit…

Q: The load per phase of a balanced 3Ø wye connected load is 8 + j6 Ohms per phase. This is connected…

A: A balanced star connection contains three-phase voltages that are dispersed 120 degrees apart yet…

Q: A given pressure transducer is designed to have a linear relationship between an input pressure and…

A: Pressure transducer is a device which converts the pressure acting upon it to a electrical signal.…

Q: esign consideratio of electrical installation system for commerical building

A: According to the question, we need to discuss the design consideration of the electrical…

Q: Please don't copy i need answer for my assignments. A 3-phase bridge inverter is operated from…

Q: explain why Two coils are said to be mutually coupled if the magnetic flux Ø emanating from one pass…

A: The magnetic fields in one of the coils tend to join with the other when two coils are placed close…

Q: 7. A stepper motor with three phases and one pole pair. Calculate the resolution of the motor and…

A: Given a stepper motor with 3 phase and 1 pole pair, so Number of stator stacks, Ns=2×3=6 Number of…

Q: Determine fundamental period of given signal x(t) = 2 cos 1.5 nt + sin 3.5 t

Q: substation auxillaries

A: Transformer- A device that transfers the electrical energy between two electrical circuits which are…

Q: In a 8 bit microprocessor, estimate the number of distinct opcodes present.

A: The solution is provided in the following section.

Q: Problem 4. Determine the value of voltage V shown in Figure 5.6. 4Ω 50 V- Figure 5.6 65 V

A: Given circuit,

Q: Q2:- For the series-parallel network of Fig. 1: a) Calculate Zr and Yr.b) Determine Ir and h.c) Find…

A: Given data,

Q: Table 3: Summing Amplifier Measurements c component) ac component) (de component) Table 4: Summing…

A: The Superposition theorem states that, for any linear system, the voltage or current in any branch…

Q: The denominator of the transfer function for a LPF is s² + s + 25. a) Find On, and Q. b) Is the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 10. A capacitor is connected across a 120 V, 60 Hz supply. An ammeter indicates 5 A and a wattmeter…

A: Since you have posted the questions with multiple subpart so we are supposed to answer 3 subpart.

Q: clamped cubic spline S for a function f is defined by + + 7 (x − - - 5(x) = {a + b(x-2) - c(x - 2)²…

Q: In the circuit shown above, the initial voltage across capacitor is 2 V and I is a unit step current…

A: The required parameters can be obtained by considering the state of the circuit at t=0 and after…

Q: (c) A transmission line, modelled through a series reactance X = 0.4 p.u., supplies an electrical…

Q: An energy meter has a meter constant of 600rev/kwh when correctly adjusted. If the lag adjustment is…

Q: The domestic load in residential building comprises of the following: 6 lamps of 55 watt each, 4…

Q: At 20 km in free space from a point source, the power density is 200 μW/m². What is the power…

Q: A cubic spline S for a function f is defined by: -2≤x≤0 - S(x) = {x³ = x + 1 lax³ + bx² + cx+d 0≤x≤2…

A: We need to select correct option for given function

Q: 1.a. Section 300.15(C) requires a fitting to be installed on each end of a conduit or tubing being…

A: 1.a. According to NEC section 300.15(C), A conduit or box body shall not be required where cables…

Q: 2.11 Given x(t) as drawn in the figure, sketch and label each of the following signals: ~ -1 (a)…

A: Note: As per the policy we can solve only 3 sub-parts, please re-upload the remaining part as a…

Q: The circuit shown below is a dc model of a residential power distribution circuit. Use the…

A: In the given circuit, there are three meshes. Here, we'll use mesh-current method to find branch…

Q: enumerate at least 3 uses of coils/inductors.

A: The objective is to determine the use of coil and inductor.

Q: 8. A 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical…

A: Given, A 3-phase induction motor has Slip, s=2%=0.02 Input power, Pin=1000 W

Q: A 2500 V, 50 Hz, 1000 hp 0.85 PF leading four poles Y-connected synchronous motor has a synchronous…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: 17. Four electricians are discussing the size of boxes that must be installed to allow for the…

A: Here four electricians are discussing about the size of boxes that must be installed to allow for…

Q: If the power level of an amplifier reduces to half, the db gain will fall by (i) 0.5 db (ii) 2 db…

A: Given, Power level of an amplifier is reduces to half.

Q: H Vcc - 12 V c-2 MA Nc Rx B = 80 Ve=7.6 V VE = 2.4 V

A: We need to find out the value of unknown resistance value for given circuit

Q: A charge q = 4.11 * 10-9 C is placed at the origin, x = 0, and a second charge equal to -2q is…

A: Given: q=4.11×10-9 C at x=0-2q=-8.22×10-9 C at x=1 m

Q: 3. In an ideal op-amp, which is not true? a) Open loop voltage gain is infinite b) Input resistance…

A: The input resistance of an ideal op amp is infinite so input of the op amp is open terminal so no…

Q: Implement the Boolean function F = xy + x ′ y ′ + y ′ z. With AND, OR, and inverter gates.

A: The boolean function to be implemented is, F=xy+x'y'+y'z The above boolean function will have three…

Q: 4. A 1000 KVA transformer has a reactance of 5%. Its reactance at 2000 kVA base is (1) 5% (iii) 20%…

A: Given: Rated kVA = 1000 kVA Base kVA = 200 kVA Reactance of rated kVA = 5 %

Q: A capacitor in an LC oscillator has a maximum potential difference of 15V and a maximum energy of…

Q: For the network shown, find currents i(t) and iz(t) for t > 0. 50 V لله الام 502 i₂ (1) 20 µF i2 (1)…

Q: A single energy meter has a meter constant of 200rev/kwh. When supplying a non-inductive load of 4.4…

Q: A white noise of magnitude 0.001 μ W/ Hz is applied to an RC low-pass filter of R = 1 KQ and C = 0.1…

A: Given, The input noise power, Pin=0.001 μWHz RC low pass filter with resistance, R=1 kΩ Capacitance,…

Q: Q2 The circuit in Figure Q2 is an active filter. (a) (b) (c) (d) Derive the expression for the…

A: As per the guidelines of bartleby i need to answer first three subparts only so kindly repost other…

Q: 1. Which of these is incorrect for an operational amplifier? a) It has a high voltage gain b) It is…

A: The solution is provided in the following section.

Q: Q6:- For the system in Fig. 5: a) Find Pr. Qr. ST, Vr and the power factor Fp. b) Draw the power…

A: Given:

Q: Which one of the following rectangular values is equivalent to the polar form 20 / 55⁰? 16.38 +j…

A: Given: Value in polar for, R∠θ=20∠55°

Q: Explain why it is important that the stimulus signals in a testbench be synchronized to the inactive…

A: The stimulus signals in a testbench to be synchronized to the inactive edge of the clock of the…

Q: Use words (not an equation) to describe one of the reciprocal identities.

A: Calculus aids in comprehending how values related by a function change over time. It is utilized in…

Q: 5. Find x[n] for each DTFT given below: (a) Xa(w) = 1+e-jw3 (b) Xa(w) = e-jw1.5, WE [-π, π) ㅠ, (c)…

Q: Consider a causal and stable continuous time filter that has a system function- Ha(s) (s+1)/(s+2)²…

A: Impulse Invariance Technique: In this technique, the sampling frequency time period provides the…

Q: compare between electrification of residential and commercial installationf

A: Compare between electrification of residential and commercial installation 1. Typically, commercial…

Q: 7. a) Rr: F R1=4Q www b) 1: . 써 R2=4Q

A: As per the guidelines of Bartleby we supposed to answer first question only since the remaining…

Q: the stator of 3 phase induction motor has 3 slots per pole per phase .if supply frequency is…

A: Given data, No. of phases (u)=3 Frequency f= 50 Hz Slots per pole per phase= 3

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

2. The load per phase of a balanced 30 wye connected load is 8 + j6 Ohms per phase. This is
connected to a 30 supply which is 230 cis 0°. Determine the line currents, power factor,
P, Q and S of the system.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The load per phase of a balanced 3Ø wye connected load is 8 + j6 Ohms per phase. This isconnected to a 3Ø supply which is 230 cis 0°. Determine the line currents, power factor,P, Q and S of the system.
A balanced delta-connected load has phase impedances of 4+j3 Ohms. It is connected to balanced transmission lines, with Vab = 1.5kV @ 15 degrees. a) What is the current through each of the load phases? b) What is the current through each of the transmission lines? c) Which ACSR cable should be used for these transmission lines to give a 20% current rating margin for this load?
Determine the line current of a Y-connected balanced three-phase load, consuming 300 kW at power factor = 0.8 lagging and operating at 480 V. Work on PER UNIT with Sbase = 375 kVA and Vbase = 480V. Choose the best answer.
Consider the balanced 3-phase circuit shown below (a) Sketch the single phase equivalent circuit. Show all values on the sketch. (b) Calculate the following: the total complex power absorbed by the wye connected load. the phase current, ICA.
A balanced three-phase ∆- connected source has a line voltage 120 V. It is connected to a load via a three-wiretransmission line. The per-phase impedance of the ∆-connected load is 30 + j120 Ω. The impedance of each wireof the transmission line is 2 + j4 Ω.How much power is dissipated by the load? How much power is dissipated in transmission line? Power factor of load?
A balanced, positive-sequence, Y-connected voltage source with Eab = 480∠0o volts is applied to abalanced-∆ load with Z∆ = 30 ∠40o Ω. The line impedance between the source and load is ZL = 1 ∠850 Ω.for each phase. Calculate the line currents, the ∆ -load currents, and the voltages at the load terminals.Recall that ZY = Z∆/3
A 220-V, 3- φ voltage is applied to a balanced delta-connected 3- φ load of phase impedance (15 + j20) Ω. Find the line voltage in volts
A balanced delta connected load of 14+j16 ohm per phase is connected at the end of three phase line. The line impedance is 4+j6 per phase . The line is supplied from athree source with a line to line voltage of 207.85 Vrms. Tnaking phase voltage Va as reference determine the following: a) I in phase a b) Total complex power supplied from the source c) Magnitude of the line to line voltage at the load terminal.
A delta-connected balanced 3 phase load is supplied from a 3 phase 400 V supply. The line current is 20 A and power taken by the load is 10000 W. Find: i) Impedance in each branch ; and (i) The line current, power factor and power consumed if the same load is conneted in star. Ans. 34.6ohms, 20/3 A, 0.7217, 3330 W
A wye-connected unbalanced load, Za = 10 angle 36.9 , Zb = 10 angle -36.9 , and Zc = 10 angle 0 are connected across a balanced 130-V, 3-phase system. Determine the reading of two wattmeters with line c as common.
In a balanced three phase system, load 1 draws 60 kW and 80 leading kVAr whereas load 2 draws 160 kW and 120 lagging kVAr. If line voltage supply is 1 kV, find the line current supplied by the generator. Both loads are 3-∅ loads.Single line text.
In the following 3-phase balanced system, calculate the line currents. Depends on the load voltage source is va(t)=100.cosωt. Phases b and c 120 degrees offset. Does the current flow a within delta link? Prove and calculate.