A balanced delta connected load of 14+j16 ohm per phase is connected at the end of three phase line. The line impedance is 4+j6 per phase . The line is supplied from athree source with a line to line voltage of 207.85 Vrms. Tnaking phase voltage Va as reference determine the following: a) I in phase a b) Total complex power supplied from the source c) Magnitude of the line to line voltage at the load terminal.

A balanced delta connected load of 14+j16 ohm per phase is connected at the end of three phase line. The line impedance is 4+j6 per phase . The line is supplied from athree source with a line to line voltage of 207.85 Vrms. Tnaking phase voltage Va as reference determine the following: a) I in phase a b) Total complex power supplied from the source c) Magnitude of the line to line voltage at the load terminal.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.25P

See similar textbooks

Similar questions

In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
One advantage of balanced three-phase systems over separate singlephase systems is reduced capital and operating costs of transmission and distribution. (a) True (b) False
The IAC current of a balanced three-phase delta connected load is known as 10 Amps (-10 degrees) and the VAB voltage as 20 Volts (10 degrees). Accordingly, calculate the following expressions by considering the positive phase sequence. A) IAB=? B)load impedance=? C)IBC=?
In the above figure, a single line model of a three-phase power system is given. Base power 50MVA, base voltage 13.8kV according to its value, a) Per-unit values of power system circuit elements according to the given base power and base voltage values. calculate. b) The perunit you calculate by drawing the equivalent impedance circuit for one phase of the power system given in the figure. show on the values.
A balanced three phase inductive load is measured by a single wattmeter using the current transformer method which has a reading of 100 watts. For the same load, it is measured again, using potential lead shift method wherein the wattmeter is placed at line 2. If the wattmeter reading across lines 1 and 2 is -1,200 watts, voltage across lines 3 and 2 is 200 bar angle 60 degrees, and the current at line 2 is 75 amperes, calculate the power factor. Assume voltage across lines 1 and 2 as reference voltage.
In a three-phase system voltage, assume that the phase-to-neutral voltage at phase “b” is considered as the reference (zero phase angle). 1. State the positive sequence and the negative sequence. 2. Solve the following for both sequences: a. the line-to-neutral voltages : VAN ,VBN and VCN b. the line-to-line voltages : VAB , VBC and VCA
For a Y-connected source and load, which quantity does NOT have an identical counterpart in the single-phase equivalent circuit?
A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced delta connected load. For the system, additional information are as follows: Vbc = 211 cis 220 degrees volts; and true power per phase is = 1239 watts, with 0.68 power factor lagging What is the angle of the line current Ib in degrees?