2. The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3080 mm?. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C. 5.00 m (1) 3.50 m

2. The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3080 mm?. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C. 5.00 m (1) 3.50 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An overhang beam is loaded as shown below. The beam cross-section was butlt by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t= 9mm Flange Width, B, -112.5 mm Web Thickness, t. -9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,-200 MPa on single shear, a, =260MPa on double shear. 1. determine the location of centroid, ȳ, from top of the beam in mm 2. determine the moment of inertia, I, of the section in mm4 3. determine the maximum allowable moment, Mall, inkn-m, base on the beam's cross section.
A square hollow steel strut with a wall thickness, t_{1} = 10 mm is pin connected to two gusset plates, having a thickness t_{2} = 12mm which are welded to the base plate having a thickness of 12 mm and fastened to a concrete base by 4-16 mm Ø anchor bolts. Diameter of pin is 16 mm. Compressive load P = 48kl , θ= 30°. Calculate the bearing stress between the strut and the pin in MPa.
2. The structure is used to support a distributed load of = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3080 mm2.The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if P=15 kN
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Thickness, tf=9mm Flange Width, B=112.5 mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear 1. Determine the location of centroid, ȳ, from top of the beam in mm
The plate shown is fastened to the fixed member to three 10-mm diameter rivets. Compute the value of the loads so that the average shearing stress in the rivet does not exceed 70 MPa. F= 74
A square hollow steel strut with a wall thickness, t_{1} = 10 mm is pin connected to two gusset plates, having a thickness t_{2} = 12mm which are welded to the base plate having a thickness of 12 mm and fastened to a concrete base by 4-16 mm Ø anchor bolts. Diameter of pin is 16 mm. Compressive load P = 48kl , θ = 30°. Calculate the shear stress in the pin in MPa.
A horizontal beam AD is supported by an inclined strut CB carries a load W = 2.4KN at the position shown. The strut which consists of one bar is connected to the beam by a bolt passing through the three bars meeting at joint C. BC is 75mm wide and 10mm thick strut while AD is 100mm wide by 10mm thick rigid bar. (a)What is the minimum required bolt diameter in at C if the allowable bolt shear is 68MPa? (b)Determine the stress in strut BC. (c)Determine the bolt stress at A if its diameter is 20mm.
The offset link has a width of w=200mm and a thickness of 40mm. The allowable normal stress is 80 MPa. Determine the maximum load, P, that can be applied to the cables.
The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
A welded connection is in equilibrium under the action of the four forses showin in figure . Knowing that FA=8 kN and FB= 052 kN,determine the magnitudes of the other two forces.
The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b = 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi.