2. Use the following data definitions for the following questions: myBytes BYTE 10h, 20h, 30h, 40h myWords WORD 8Ah, 3Bh, 72h, 44h, 66h Fill in the requested register values on the right side of the following instruction sequence. mov esi, OFFSET myBytes al, [esi] ; a. AL - mov al, [esi + 3] ;b. AL = mov esi, OFFSET myBytes mov mov ax, [esi] ; с. АХ mov eax, DWORD PTR myWords ; d. EAX-
Q: Assume X address is 29D, find the value of AX for each of the following instruction .Data X byte 12,…
A: Given:
Q: B. For data type double, what lower bound on the CPE is determined by the critical path? C. Assuming…
A: The solution for the above given question is given below:
Q: NASM CODE, modify the code below Write an assembly program for the processor family x86-32 that…
A: given data, section .datamsg db "The largest number is: %d", 0xa,0v1 equ -47v2 equ 32v3 equ 21num1…
Q: 4- Assume BX= 6A83h, AH= 89h, DX= 5678h, SI= 1234h. Select an OR instruction that will: (a) OR BL…
A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: Find the machine codes of following 8085 instructions and in each case identify the opcode part, and…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: 1. Suppose we have a 32-bit MIPS word containing the value 0×008A1021. We want to determine what…
A: 3. a. Writing the instruction in binary format: Binary instruction formation show the relationship…
Q: Carefully study the following data definitions and answer the question shown below. Assume…
A: In MIPS, all variables are memory-aligned by default. Thus : All byte-variables (1 byte each) will…
Q: Q2) Answer the followings: (a) What is the main difference between op code & operand? (b) Assume…
A: According to the question , we have to answer (a) what is the difference between opcode and operand.…
Q: 2. a) Explain the following code and indicate in each case the type of addressing mode used. i) СМА…
A: Given second step different types of instructions are explained, addressing mode of 8086are…
Q: 7-lf we assume we place the following MIPS code starting at location 8000 in memory, what is the…
A: 1) SLT $t2 $zero $t0 Binary: 00000000000010000101000000101010 Hex: 0x0008502a 2) BNE $t2 $zero…
Q: Analyse the following from program and specify the data in registers and memory location after the…
A: The first instruction ORG 1000H sets the current address during assembly to be 1000H. The second…
Q: (3) (a) Write an assembly language program with proper comment for the following : A block of data…
A: Given:
Q: . 2) You are required to write an Assembly Language program segment to perform the operation Ci =…
A: Given 2. 2) You are required to write an Assembly Language program segment to perform…
Q: Q3: The original contents of CX, AX, memory location Beta, and carry flag (CF) are FFE116, 11AB16,…
A: Answer: I have given answered in the handwritten format
Q: 3. Assume the following 64b register contents: x5 O×0000000OODEADFAD, x6 = 0×BADBEEF011223344 For…
A: Answer is given below .
Q: Assume that DS=D4500h, SS=2000n, BX =2100, Sl=1486, DI 8500r, BP=7814h, and AH=25h. 1-Show the PA…
A: Given: We are given a problem in which multiple registers with their content are given. Goal: We…
Q: Convert the following C code to MIPS assembly code. Assume the base address of array is stored in…
A: Find: Write MIPS assembly code for the given c code instruction. Answer: Please find the MIPS…
Q: Translate the following C++ program into MAL (MIPS Assembly Langage). Your solution should have all…
A: $g++ -o main *.cppmain.cpp:2:7: error: expected nested-name-specifier before ‘std’ using std: :…
Q: Assume that DS=4500h, SS=2000h, BX =2100h, SI=1486h, DI 8500h, BP=7814h, and AH=25h. 1-Show the PA…
A: Goal: We have to find out the content of AH after every instruction execution. Also find out which…
Q: Q1/ Two word - wide unsigned integers are stored at the physical memory addresses 0400H and 0402H…
A: 1.mov 3 to eax and mov 4 to ebx and also use mul ebx to put 12 in eax2. now mov eax to ecx to…
Q: Write in MIPS Assembly language a well-documented program consisting of the two following functions.…
A: .globl main .textmain: jal driver # call function driver…
Q: 3. Consider the following register transfer statements for two 4-bit registers R1 and R2. xT: R1 R1+…
A: Given register transfer statements Construct hardware implementation
Q: What will be the contents of AX, BX, CX and DX registers after the execution of the following…
A: Here i explain line by line. figure 1:
Q: 3. a) What is the three-instruction cycle model of a microprocessor? b) Differentiate between…
A: Answer: a) b) c) i) ii)
Q: (b) For the following code, draw the resulting memory diagram. ; Main Program, Start 1000H:200H…
A: Answer: I have given answer in the brief explanation.
Q: Q2) Answer the followings: (a) What is the main difference between op code & operand? (b) Assume…
A: a) Difference between opcode and operand. sr. no Op-code Operand 1 Op-code means operation…
Q: 12. Consider the following instruction: Instruction: AND Rd,Rs,Rt Interpretation: Reg[Rd] = Reg[Rs]…
A: The question is on choosing the correct option from the given options considering the given…
Q: 4. Write an instruction sequence to configure the 80386DX as follows: interrupts not accepted; save…
A: Introduction of Flags register(a special register with individual bit positions that indicate the…
Q: The hypothetical machine has two I/O instructions: 0011 = Load AC from I/O 0111 = Store AC to I/O In…
A:
Q: The following tables contains memory dump and contents of few registers, as follows: k**** add cont…
A: Here have to determine correct option for value of operand 4[eax].
Q: 2. Two word-wide unsigned integers are stored at the physical memory addresses 00A0016 and 00A0216,…
A: Two word-wide unsigned integers are stored at the physical memory addresses 00A0016 and 00A0216,…
Q: 3. Suppose we have a 32-bit MIPS word containing the value Ox008A1021. We want to determine what…
A: Hey, since there are multiple questions posted, we will answer first question. If you want any…
Q: Question 2:Chapter (2): 2.1. The following problem deal with translating from Java to MIPS. Assume…
A: Answer: 2.1. We need to obtain the MIPS version of the given java code as x = B[5] + z $s0 = x $s1 =…
Q: 2-Two word wide unsigned integers are stored at the physical memory addresses 00A00 and 00A02,…
A: Given two unsigned integers stored at the physical memory address 00A00 and 00A02. Need to write…
Q: [1.1] Consider the following instruction: or rd, rs1, rs2 Instruction: Interpretation: Reg[rd] =…
A: (1.1) a) instruction: and rd, rs1, rs2RegWrite = 1MemRead = 0ALUMux = 0MemWrite = 0ALUOp = AddRegMux…
Q: 4. By assuming that 35 is a two digit number, consider memory storage of a 64- bit word stored at…
A: Given question has asked to assume memory word 35 in a byte addressable memory and also considering…
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given: We are given various registers with values stored in them. Register such as SS, DS, ES, CS,…
Q: : . Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore…
A:
Q: 2. a) Explain the following code and indicate in each case the type of addressing mode used. i) CMA…
A: This insertions are related to microprocessor. Above question explained in step send.
Q: Assume that registers $s0, and $s1 hold the value 0x80000000 and 0×D0000000, respectively. (0x:…
A: a. $s0 =0x80000000 = 1000 0000 0000 0000 0000 0000 0000 0000 (32 bits) $s1 = 0xD0000000…
Q: For the following C++ statement, what is the corresponding MIPS assembly code? Assume that the C++…
A: Given :- f = g + (h - 5) Assume :- f = $s0 g = $s1 h = $s2
Q: Question 01 : (a) Write an assembly language program for the Intel 8086 microprocessor that adds two…
A:
Q: 2.3 [5] For the following C statement, what is the corresponding MIPS assembly code? Assume that…
A: To do: For the given C statement write the MIPS assembly code.
Q: What will be the content of memory location 250 in decimal after exclusion of the following program…
A: We are given 8 instructions and we are going to see what will memory location 250 will contain after…
Q: (e) What is an object file, and what does it contain?
A: (e) What is an object file, and what does it contain
Q: 52-Two word wide unsigned integers are stored at the physical memory addresses 00A00 and 00A02,…
A: Given:- Two word wide unsigned integers are stored at the physical memory addresses 00A00 and 00A02…
Q: 2. Consider the following high-level code snippet. Assume that unsigned integer values are stored in…
A: code main: push rbp mov rbp, rsp sub rsp, 1456 lea rax,…
Q: e) Use the following data definitions: bytel byte2 wordl OFFh,1,2 14h BYTE ΒYTΕ WORD OFFFFH,1,2…
A: Data definition byte1 BYTE 0FFh ,1 , 2 byte2 BYTE 14h word1 WORD 0FFFFh , 1 , 2 word2…
Q: Consider the following assembly code: Description Read data from memory and store in R1. Memory…
A: Here, I have to provide a solution to the above question.
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- Please look at the entire text below. Please solve and show all work. Thank you. What is the corresponding MIPS assembly code for the following C statement? Assume that the variables f, g, h, i, and j are assigned to register $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. B[8] = A[i−j] Translate the following C code to MIPS. Assume that the variables f, g, h, i, and j are assigned to register $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 8-byte words: B[8] = A[i] + A[j] Assume that registers $s0 and $s1 hold the values 0x80000000 and 0xD0000000, respectively. What is the value of $t0 for the following assembly code? add $t0, $s0, $s1 Is the result in $t0 the desired result, or has there been an overflow? For the contents of registers $s0 and $s1 as…For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays (A and B) are in registers $s6 and $s7, respectively. Also, assume that A and B are arrays of words. B[f-j] = B[i] + A[g]Convert given code to LEGv8 code:int f, g, y //global 64-bit variablesint sum (int a, int b) { // at memory address X0+1000.return (a +b)} int main (void) // at memory address X0 + 800{f=2;g=3;y= sum (f, g);return y;}Convert this code, making valid assumptions about registers and register use. Notethat brackets and global variable declarations are not affecting the addresses of the instructionsin memory.
- Please solve and show all work. For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 8-byte words: f = (g+i+2) + (h − 8); B[8] = A[i-9] + A[j+8] + 7;Rearrange the following code to minimize the total number of cycles, assuming that a dependent instruction following the load will need two clock cycles of delay before getting the data. Load r1, 64 (r2)Add r2, r2, r2Sub r3, r4, r1Load r4, 32 (r4)In the Intel 8086 microprocessor, suppose the register AX contains the data 35AB H. What will be the contents of AX after executing the following programs? Assume that the initial content on the Carry Flag (CF) is one for all the calculations. You MUST clearly show ALL your steps in obtaining your final result for getting full and/or partial credit. Please present your final result in Hexadecimal format. (a) MOV CL,04H SHR AX,CL RET (b) MOV CL,04H RCR AX,CL RET
- (ASM) For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. B[f] = A[(i-h)+j] + g;1. The hypothetical machine has two I/O instructions: 0011 = Load AC from I/O 0111 = Store AC to I/O In these cases, the 12-bit address identifies a particular I/O device. List the steps for every execution for the following program and illustrate using table that explain the process below : a. Load AC from device 5. b. Add contents of memory location 940. c. Store AC to device 6. d. Assume that the next value retrieved from device 5 is 3 and that location 940 contains a value of 2. Please pointing a, b,c ans. Because one I already upload this question and I didn't understand which one is and of a...please write ans a, b , c pleasePlease solve and show all work. Thank you. What is the corresponding MIPS assembly code for the following C statement? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 4-byte words: f = g + (h − 5); B[8] = A[i] + A[j+1];
- Find the machine codes of following 8085 instructions and in each case identify the opcodepart, and register/ memory reference bits. Also mention the length of opcode, number of bytesin the instruction.MOV A, M;MVI C, data;PUSH B;ADC B;XRA L;JNZ addressLDAX B Translate the following Assembly program of 8085 into machine code (hex format) MVI C, 20LXI H, 1500hMVI A, 00next; MOV B, MADC BINX HDCR CJNZ nextSTA 1600hHLTAssume that the program is to be stored in memory starting at address 1000h Find out the number of machine cycles and the number of T-states taken by the following8085 instructions. In each case give an explanation for your answer.(i) ADC D(ii) ADI 05(iii) JMP 1500h(iv) JNZ 1500h(v) LDAX B(vi) MOV A, B(vii) LDA 1300h Draw a complete connection diagram of a computer system with 8085 as processor, a four 1KRAM, and four 1K ROM chips. Give the address range for each RAM and ROM chips. Translate the sumArray function (written in C below) to 8085 assembly…For the MIPS assembly instructions below, what is thecorresponding C statement? Assume that the variables f, g, h, i, and j areassigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume thatthe base address of the arrays A and B are in registers $s6 and $s7,respectively. Note: for each line of MIPS code below, write the respective Ccode. After that, write the corresponding C code for the MIPS.sll $t0, $s0, 2add $t0, $s6sll $t1, $s1, 2 add $t1, $s7, $t1lw $s0, 0($t0)addi $t2, $t0, 4lw $t0, 0($t2)add $t0, $t0, $s0sw $t0, 0($t1)Assume the following values are stored at the indicated memory addresses and registers Address Value 0x100 0xaaa 0x104 0x123 0x108 0x12 0x10c 0x10 Register Value %eax 0x100 %ecx 0x1 %edx 0x3 Fill up the following table: %eax 0x104 $0x108 (%eax) 4(%eax) 9(%eax,%edx) 260(%ecx,%edx) 0xFC(,%ecx,4) (%eax,%edx,4)