2. Water flows at a rate of 90lt/s from reservoir A to reservoir B through three concrete pipes connected in series as shown. Considering the water surface elevation in reservoir A designed to be 350m, find the water surface elevation in reservoir B. Neglect all minor losses. 350m Res A Res B L=6000m L-4000m L3=2500m Di=300mm D2=230mm D3=200mm fi = 0.018 f2-0.015 f=0.012

2. Water flows at a rate of 90lt/s from reservoir A to reservoir B through three concrete pipes connected in series as shown. Considering the water surface elevation in reservoir A designed to be 350m, find the water surface elevation in reservoir B. Neglect all minor losses. 350m Res A Res B L=6000m L-4000m L3=2500m Di=300mm D2=230mm D3=200mm fi = 0.018 f2-0.015 f=0.012

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through a corrugated metal pipe (D=1.2m) at a normal depth of 0.6m ata constant slope of 0.002. Determine the discharge, Q, through the pipe using Manning’s formula.
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses.
Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3connected in series with length of 170 m, 300 m, 210 m respectively. Thedifferent in water surface levels in two reservoirs is 12 m. The friction coefficientfor pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based onTable 2 and the setting given, determine the flowrate of the flow if the entranceloss coefficient is 0.25 considering :(i) minor losses; and(ii) neglecting minor losses pipe 1 =230(mm) Pipe 2 =330(mm) Pipe 3 = 430(mm)
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
A rectangular gate 1.60 m wide and 2.40m high has water on one side and is inclined 45\deg with them horizontal. Water is 1.50m above the top of the gate. Evaluate the location, in meters, of the center of pressure from the top of the gate. a. 1.34 b. 1.49 C.1.56 d. 1.64
Water flows uniformly at a depth of 1.65m in a rectangular canal 4.3m wide, laid on a slope of 1.0m per kilometer. Using n = 0.016, what is the velocity of the water flow? Use Manning's c.
*hydraulics *Use handwritten Water Flows uniformly at a steady rate of 0.40 m3/s in a very long triangular flume which has side slopes of 1:1. the bottom of the flume is on a slope of 0.006 and n=0.012. Determine the critical depth of flow Choices: A.) 0.504 m B.) 0.604 m C.) 0.704 m D.) 0.804 m
1. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.) 39.5136 b.) 12. 9517 c.) 99.9358 d.) 30. 4889 2. What gage pressure p1 in kPa, is needed to provide the given flow rate? a.) 1121kPa b.) 1328kPa c.) 1692kPa d.) 1725kPa
Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16 ft and water depth of 4.5ft. The channel bottom drops 0.1ft every 100ft. Length, n=0.015. Show Complete Solutiona. Compute the velocity in ft/s (using Manning, Kutter)b. Compute the flow rate in ft3/s (using Manning, Kutter)
In the branched pipe system below, water is flowing at 0.0142 m3/sin a new, clean DN 100 Schedule 40 pipe (ID = 0.1023 m) at A. The flow splits into two new, clean DN 50 Schedule 40 pipes (ID = 0.0525 m; A = 0.00216 m2) as shown and then rejoins at B. Call the 30 m branch“a” and the other branch “b.” The friction factor in Branch ais 0.021, and the friction factor in Branch bis 0.0215.(Note that if friction factors weren’t given, you’d need to make initial guesses and iterate!)Calculate the flow rate in each of the branches. Include the effect of all minor losses in Branch bbut ignore the tee junctions. The total length of the pipe inBranch bis 60 m. The elbows are standard.(Remember to check that your final answers follow continuity!)
1. A 3.1 – m wide rectangular flume carries water at 5.60 m3/s. The bed slope is 0.00078 and n = 0.010. At a certain section, the depth is 92 cm. a. How far therefrom is the depth 80 cm? b. What is the slope of the egl? c. What is the headloss? 2. A rectangular channel 1.8 m wide conveys water at a depth of 1.2 m. a. What is the velocity of flow if it is laid on a slope of 0.002 and n= 0.012? b. What is the discharge if the channel slopes 0.1° and n = 0.016? Use Kutter’s formula for C. c. What is the velocity of flow if S = 0.000263 and f = 0.02?
Reservoir A has an elevation of 100 m. A pipe is connected from Reservoir A to Reservoir B. It has a length of 1000 m. and diameter of 600 mm. A pump is installed near Reservoir A and has a rating of 500 hp. If C = 110, rate flow is 550 L/s, a. Determine the head supplied by the pump in meters. (Answer: 69.132) b. Compute the max. elevation in meters of Reservoir B that the pump could supply. (Answer: 162.025)