2.14. A pump is driven by a two-speed motor having speeds of 1750 and 1185 rpm. At 1750 rpm, the flow is 45 gpm, the head is 90 ft, and the total efficiency is 0.60. The pump impeller has a diameter of 10 in. a. What values of Q, H, and ns are obtained if the pump runs at 1185 rpm? b. Find the specific speed and the specific diameter of the pump (at 1750 rpm).

2.14. A pump is driven by a two-speed motor having speeds of 1750 and 1185 rpm. At 1750 rpm, the flow is 45 gpm, the head is 90 ft, and the total efficiency is 0.60. The pump impeller has a diameter of 10 in. a. What values of Q, H, and ns are obtained if the pump runs at 1185 rpm? b. Find the specific speed and the specific diameter of the pump (at 1750 rpm).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.calculate the pressure in a hydraulic system if the pump delivers 180 liters /min, and the engine has a power capacity of 75kw.2.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system tool , to know that the engine is capable to support the hydraulic system if a pump delivers 110 liters per minute and the pressure is 227bar.
A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. (a)At what speed, in RPM, should the turbine run under a head of 11 meters? (b)What horsepower would be developed?
Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid against a head of 25 m. The diameter of the impellers being 24 cm and the speed of 1800 rpm. A pump is to be made up with a number of stages in series of similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloliters/min against a totalhead of 250 m. Find the diameter of the impellers and the number of stages required in this case. Answer: D = 46.63 cm, n = 6 stages
1. The pressure in a hydraulic system has 120 bars and the engine power of 55.21 kw. Calculate the capacity of the pump to supply the system?2. The above pump had an actual flow of 90 liters/minute at 207 bar. Calculate the power of the hydraulic engine system?
The volumetric efficiency of a certain piston pump is 97%. If the pump delivers 14 L/min at 1200 rpm, find the Volumetric displacement of the pump. A system requires a pump to deliver 30 gal/min at 1500 lbf/in2 at an engine speed of 2000 rpm. calculate theoretical pump displacement, engine torque to drive the unit, and horsepower. A piston pump operating at 1,150 rpm and 3000 Ibf/in2 delivers fluid at 10 gal/min. If the pump has an overall efficiency of 94%. What is the input torque from the driving unit? A pump operating at 2,000 Ibf/in? and delivering 5 gal/min requires 7 bhp to drive the input shaft. Compute the overall efficiency of the pump.
PUMP DISCHARGES 150 LITERS PER SECOND OF WATER TO A HEIGHTOF 80 METERS. IF THE EFFICIENCY IS 80% AND THE SPEED OF THE PUMP IS 1800 RPM, WHAT IS THE TORQUE IN N-M TO WHICH THE DRIVE SHAFT IS SUBJECTED?
A water pump develops a total head of 200 ft. The motor efficiency is 87.5%. If the power rate is 1.5 cents per kw-hr, what is the power cost in cents per minute for pumping 1000 gal/hr
A water pump develops a total head of 200 ft. The pump efficiency is 80% and the motor efficiency is 87.5%. If the power rate is 1.5 cents per kw-hr, what is the power cost for pumping 1000 gal/hr?
a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating at a speed of 1800 rpm. if the speed held constant and the impeller diameter is change to 203.2 mm, what is the new dischange og the pump in liters per second
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.
a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
A centrifugal pump with a 3-inches diameter impeller rotating at 1150 rpm delivered 400 gpm of water 80ºF at 250 ft total head. Find the impeller diameter of a geometrically similar pump rotating at 1750 rpm delivering 500 gpm. What is the total head of the second pump.