2.18 Consider the following circuit: a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across each half of the secondary. d) Sketch the voltage waveform across RL e) What is the peak current through each diode? f) What is the PIV (Peak Inverse Voltage) for each diode? 120 V ms Dz 1.0 k elle elll

2.18 Consider the following circuit: a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across each half of the secondary. d) Sketch the voltage waveform across RL e) What is the peak current through each diode? f) What is the PIV (Peak Inverse Voltage) for each diode? 120 V ms Dz 1.0 k elle elll

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Consider the circuit in Figure 2–75 .(a) What type of circuit is this?(b) What is the total peak secondary voltage?(c) Find the peak voltage across each half of the secondary.(d) Sketch the voltage waveform across RL.(e) What is the peak current through each diode?(f) What is the PIV for each diode?
Consider the circuit. a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across the each half of the secondary. d) Sketch the voltage waveform across RL. e) What is the peak current through each diode? f) What is the PIV of each diode?
Consider the circuit.a. What type of circuit is this?b. What is the total peak secondary voltage?c. Find the peak voltage across each half of the secondary.d. Sketch the voltage waveform across RL.e. What is the peak current through each diode?f. What is the PIV for each diode?
1. Plot the diode forward characteristics from the results obtained, and determine the cut in voltage Vγ from the sketch
1. Using first approximation, find the voltages across resistance. 2. Using second approximation, find the currents across Si diodes
For the following rectifier semiconductor diodes, 1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 download either a group data sheet or individual data sheets from the internet. Then make a comparison table which shows the following for each diode (I-IV). (I) Peak Repetitive Reverse Voltage VRRM (Working Peak Reverse Voltage VRWM DC Blocking Voltage VR) (II) Non Repetitive Peak Reverse Voltage VRSM (half wave, single phase, 50/60Hz) (III) RMS Reverse Voltage VR(RMS) (IV) ADD ANYTHING ELSE YOU SEE FIT. (V) From the table state which diodes you would use for a VRRM of 100V and 1000V (VI) Show a copy of a graph which shows the reverse voltage against typical Capacitance values, say what it shows. (VII) For any of the diodes, describe with the aid of diagrams/illustrations itsapplications in an AC to DC…
Determine the reverse voltage and reverse current for the diode in the Figure below for each of the diode models. Also find the voltage across the limiting resistor in each case. Assume IR = 1-µA. a. The value of reverse current, assuming ideal diode model. b. The value of reverse voltage, assuming ideal diode model. c. The value of voltage across the limiting resistor, assuming ideal diode model. d. The value of reverse current, assuming practical diode model. e. The value of reverse voltage, assuming practical diode model. f. The value of voltage across the limiting resistor, assuming practical diode model. g. The value of reverse current, assuming complete diode model. (in µA) h. The value of reverse voltage, assuming complete diode model. (in mV) i. The value of voltage across the limiting resistor, assuming complete diode model. (in V)
Briefly discuss the difference between Diode Piecewise-linear model, Simplified model, and Ideal device/ equivalent circuit. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each. Discuss briefly how to test junction diode.
Determine the Q-points for the diode in the circuit given below using the constant voltage drop model with Von = 0.7 V, where R1 = 44 kΩ and R2 = 23 kΩ.
For the values of R1=230, R2=230, R3=400, Vs=15. If the real diode (offset voltage=0.7V) were conduxting, then the value of voltage source Vb should be? solve correct or will dislike