i need the answer quickly 2.25 The lydranlic eylinder BD eserts on member ABC a force Pdirected akmg line BD. Kuowing that P mst have a 750-N eom-punwent perpendicular to member ABC, determine n the mgni-hale of the foree P. t) its eamponent parallel tn ABCFig. P2.25

Given Load, F = 750 N Angle = 60o Find Magnitude, P Force component

2.25 The hydranlie eylinder BD eerts on member ABC a force P directed along line BD. Kowing that P must have a 750-N com- puent perpendicular to member ABC, determine ia) the magni- hude of the foree P d) its component arallel tn ABC. Fig. P2.25

2.25 The hydranlie eylinder BD eerts on member ABC a force P directed along line BD. Kowing that P must have a 750-N com- puent perpendicular to member ABC, determine ia) the magni- hude of the foree P d) its component arallel tn ABC. Fig. P2.25

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.49P: The cables AB and AC are attached to the frame OBCD and pre-tensioned to 35 kN. Determine the...

See similar textbooks

Related questions

Q: 9A converging–diverging nozzle operates at steady state. Air as an ideal gas with k = 1.4 flows…

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 650-N load is…

A: When a push or pull applied on the object in compressible or tensile manner, it has the ability to…

Q: The single slider mechanism shown below has the following dimensions: the crank AB = 95 mm and the…

Q: Propane is a hydrocarbon that burns to produce carbon dioxide or carbon monoxide, depending on the…

Q: 5. A 4-m x 5-m × 6-m room is to be heated by a baseboard resistance heater. It is desired that the…

A: find the required power of the resistance heater.

Q: 10.25 For a flow rate of 12 L/s and turbine speed of 65 rpm, estimate the power transferred from the…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: Problem 1: Calculate the forces in the required members of the truss shown: F1 F2 F3 H F h F4 D E C…

Q: For what value Mof the clockwise couple will the horizontal component A, of the pin reaction at A be…

A: find the value of moment M when horizontal reaction at A is zero. find the value of horizontal…

Q: Calculate the polar moment of inertia of the shaded area about point O. y 33 mm 19 mm | Answer:I, =…

Q: Steam at a pressure of 1000 psia and 650 0F enters an adiabatic turbine and leaves at 65 psia. The…

Q: Determine the x-and y-coordinates of the centroid of the shaded area.

Q: ommendation, what is the factor of safety for a key under seve

A: Ans: The factor of safety is taken as 3 to 4 for key design under difficult situations.

Q: Replace the force and couple system acting on the member shown by an equivalent resultant force and…

Q: 3. A piston-cylinder device with a set of stops initially contains 0.6 kg of steam at 1.0 MPa and…

A: find the compressor work and final temperature.

Q: Determine the polar moment of inertia of the circular area without and with the central square hole.…

A: Radius of the circle=R Side length of the square, s= 1.24 R

Q: Q2/ Determine the forces at the pin ? joint (F) and the roller support (G) 30KN 20 KN 2m B 2m D 2m E…

Q: 1. In the figure shown below, two blocks are connected by a solid strut attached to each block with…

A: find the minimum weight of A to prevent motion.

Q: A hollow steel shaft, 5.8 ft long, has an outer diameter of 2.73 in and an inner diameter of 1.24…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. y 520 150 60° 60° 370 185 260…

Q: View Factor Example #2 Surface 1 is very long 0.3-m x 0.4-m "L" formed from a pair of perpendicular…

A: Given: The area of surface, A1 = 0.3 m x 0.4 m The diameter of surface 2, d = 0.1 m

Q: A uniform bar with mass M = 3.25 kilograms is shown in the diagram. hlo required to keep the

Q: B P 6. Determine the moment of the force P which is 100N at point 0, consider all sides are in…

A: To find the moment of force P about O

Q: Incorrect Determine the x- and y-coordinates of the centroid of the shaded area shown. 2", 2" 3"…

A: find the centroid of the shaded area.

Q: Consider a person standing in a room maintained at 20°C at all times. The inner surfaces of the…

Q: Water flows through a circular tube with a velocity of 2 m/s. The diameter of the pipe is 14 cm If…

Q: E 12.5 m C А 8 m 5 m

Q: 21:08 Fluid Statics.pdf 6m 12. Determine the value and location of the horizontal and vertical…

Q: The variable h designates the arbitrary vertical location of the center of the circular cutout…

Q: Determine the polar moment of inertia of the circular area without and with the central square hole.…

A: given : b = h= 1.06 R

Q: 7. One pound of an ideal gas undergoes an isentropic process from 95.3 psig and a volume of 0.6 fA°…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: The figure below shows a vapor power cycle that provides process heat and produces power. The steam…

Q: If the bearing pads at A and B support only vertical forces, determine the factor safety for the…

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 660 N, a =…

A: Consider the free body diagram for the member ABC.

Q: A hemispherical dome of 45 m diameter covers a 25 m diameter ice sink. Both ice and dome can be…

A: When an amount of heat is transferred from the one body to the another body in the form of waves or…

Q: Write the differences between the boiler mountings and accessories

A: Boiler mountings are used in boilers primarily for safety purposes. The main function of mountings…

Q: The fluid flow through a pipeline can be assumed as Unsteady flow Uniform flow…

A: Steady flow is the correct answer.

Q: An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 520 150 60° 60° 370 185 260…

A: To determine the centroid of the given segment.

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

Q: Determine the y-coordinate of the centroid of the shaded area. 65 mm 37° 37° 75 mm 65 mnt 45 mm 45…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: The following figure is a truss a joint of truss members. What will be the value of T1 and T2 if the…

Q: + REMEDIAL ACTIVITY FOR MODULE 2_MEC30-2_3Q_2122 Question 17 of 27 -/ 20 E : View Policies Current…

A: find the value P.

Q: Water flows through a circular tube with a velocity of 2 m/s. The diameter of the pipe is 14 cm. If…

A: Velocity of water, V=2 m/sPipe diameter, d=14 cm=0.14 mKinematic viscosity of water, ν=10-6…

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable…

Q: below to solve the ff: 1. Total acceleration of the end of the crank.(in/s2) 2. Angle in degrees…

Q: By the method of this article, determine the moments of inertia about the x- and y-axes of the…

A: A trapezoidal area is given below,

Q: A high strength steel band saw, 30 mm wide by 0.80 mm thick, runs over pulleys 500 mm in diameter.…

Question

i need the answer quickly

2.25 The lydranlic eylinder BD eserts on member ABC a force P
directed akmg line BD. Kuowing that P mst have a 750-N eom-
punwent perpendicular to member ABC, determine n the mgni-
hale of the foree P. t) its eamponent parallel tn ABC
Fig. P2.25

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The frame shown is subjected to a horizontal force F = {300j} N. Determine the magnitudes of the components of this force parallel and perpendicular to member AB.
Answer for the 1st part of the problem. magnitude of force A = 74 N direction of force A = 25o north of west second force = P direction of force P = α south of west arrow_forward The resultant of two forces is horizontal , it means that the y component of resultant = 0 Ry = ASin(25o) - PSin(α) 0 = (74×0.42) - PSin(α) PSin(α) = 31.08 NFor, the smallest force P , the value of Sinα must be maximum which is 1 when the value of αis 90 degree Thus, P×Sin(90o) = 31.08 N P = 31.08 N The magnitude of smallest force P = 31.08 N the direction of force P = 90 degree south of west = along - y axis= arrow pointing vertically downw
The supporting cables AB and AC are oriented so that the components ofthe 360-lb force along AB and AC are 185 lb and 200 lb, respectively. Determinethe angles α and β.
to hold the loaded wheelbarrow, our force applied to the handle is ___ the load weight 1. equal to2. more than3. in the same direction as4. less than
A square ABCD of 60 mm side is subjected to force of 10 N, 20 N, 30 N and 40 N along the sides AB, AC, BD and AD respectively. Find magnitude. direction and position of the resultant force with respect to A.
The length of the assembly shown decreases by 2.1 mm when an axial force is applied by means of rigud end plates. Determine the magnitude of the applied force (kN).
ABCD is rectangle, in which AB = CD = 100 mm and BC = DA = 80 mm. Forces of 100 Neach act along AB and CD and forces of 50 N each at along BC and DA. Find the resultantmoment of the two couples
A cable is connected to an L shaped arm OAB as shown. The magnitude off the tensile force on the cable is given as T = 2500 and angle between the segment AB of the L- shaped arm and cable = 91.229 degrees. ( use the vector approach ) A) determine the components of the tensile force on the cable which are parallel and perpendicular to segment AB of the L-shaped arm
A horizontal rigid boom OD is subjected to a vertical load P = 1000 N and is supported by two cables to a vertical supporting wall as shown. Assume point O is a hinged support. Determine the tension in cable AC and BC. (Ans. TAC = 1,414 N ; TBC = 1,751 N)
Three ropes support the weight at A. The tension in ropes AB and AC is 15 lb. Determine the tension Tin the third rope, knowing that the resultant of the three tensions is vertical.
A control rod AB is fixed with a pin connection at B. The rod is 26 in long and is at an angle of 60 degrees from the positive x-axis. A 11.9 lb force F is applied to the end of the control rod (point A) down and to the right, at an angle of α from the rod. Knowing that it creates a 253.4 in lb clockwise moment about point B, determine angle α and the perpendicular distance between the line of action of force F and point B.
The guy wire BD exerts on the telephone pole AC a force P directed along BD. Knowing that P must have a 720-N component perpendicular to the pole AC , determine (a) the magnitude of the force P, (b) its component along line AC.