2.26 The currents i, and i, in the circuit in Fig. P2.26 are 4 A and -2 A, respectively. PSPICE MULTISIM a) Find ig. b) Find the power dissipated in each resistor. c) Find vg. d) Show that the power delivered by the current source is equal to the power absorbed by all the other elements. Figure P2.26 11 0 E100 30 N 100 V 15 N 16 0

2.26 The currents i, and i, in the circuit in Fig. P2.26 are 4 A and -2 A, respectively. PSPICE MULTISIM a) Find ig. b) Find the power dissipated in each resistor. c) Find vg. d) Show that the power delivered by the current source is equal to the power absorbed by all the other elements. Figure P2.26 11 0 E100 30 N 100 V 15 N 16 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

25. Four resistance each of R ohms and two resistances each of S ohms are connected (as shown in Fig. 2.50) to four terminasl AB and CD. A p.d. of V volts is applied across the terminals AB and a resis- tance of Z ohm is connected across the terminals CD. Find the value of Z in terms of S and R in order that the current at AB may be V/Z. Find also the relationship that must hold between R and S in order that the p.d. at the points EF be V/2. [Z= R(R+2S);S=4R]
Let the following electrical circuits be, in which it is required to determine the value of the voltage V shown:Note that the two previous circuits are identical, the only difference is the load element that has been selected in each of them: in electrical network 1 the load element is resistor R3 while in electrical network 2 the element of load is resistor R1.a) Find, using Thévenin's theorem, the voltage V in electrical network 1.b) Find, using Thévenin's theorem, the voltage V in the electrical network 2.
In the circuit of Fig.2, the current through R3 is 10% of the load current supplied through its terminal. The resistances R1, R2 and R3 can be determined when the voltage and current in each resistance had been determined. Determine the following: a. The total resistance of the circuit is? b. The total current is? c. The power dissipation of R2 is?
The currents ia and ib in the circuit in Fig. P2.26 are 4 A and - 2 A, respectively. a) Find ig. b) Find the power dissipated in each resistor. c) Findvg. d) Show that the power delivered by the current source is equal to the power absorbed by all the other elements
You are required to analyze the operation of DC circuit shown in Fig.2 and apply Ohm’s law and Kirchhoff’s voltage and current laws to find all the Voltages (with the associated polarities) andcurrents (with the associated direction)for all resistors. (Show all steps, equations, and calculations). C)Your manager asked you to present an analysis for the scientific data related to DC circuit. Firstly, he asked you to replace V1 with open circuit and V3 with short circuit and do the following:a. Calculate the equivalent resistance, all currents and voltages.b. Connect the circuit in the Laboratory and fill the results in Table 2 (Show all calculations).
Q2:-For the circuit shown in Fig.(2) , find Q-point . Assume : Ing = ( 1+ Vs )* X 10
In the circuit illustrated in Fig.1, determine the following using relevant numerical data supplied (i) CurrentI0delivered by the source. (ii) Voltage at the node marked as A. (iii) CurrentI9passing throughR9. (iv) Power dissipated in the resistance,R8 (v)Req seen by the voltage source V0
The bridge circuit shown in Fig. 1 is balanced when R1=100 Ω, R2= 1000 Ω, and R3= 150 Ω. The bridge is energized from a 5V DC source. (a) What is the value of Rx? (b) Suppose each bridge resistor is capable of dissipating 250mW. Can the bridge be left in a balanced state without exceeding the power-dissipating capacity of the resistors, thereby damaging the bridge? And why?
for the fig2.24 find (a) R and (b) the power supplied by the 250V source
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
For the network in Fig 2:(a) Calculate RT. (b) Find IS, I1 and I2. (c) Calculate V3.
Solve the following Numerical problems a. What is the Output Voltage of a battery that expends 7.2J of energy in moving 1C of charge? b. A 50-ohm load dissipates 200W of power. How much is the voltage and current across the load? c. If one branch of a 120-V power line is protected by a fuse of 20-A. Will the fuse carry 10-Ohm load? d. If total resistance of a series circuit is 280-Ohm. If one of the resistance is 160-Ohm. What is the sum of other two resistances?