2.4.7. An open manometer, shown in Figure P2.4.7, is installed to measure pressure in a pipeline carrying oil (S.G. = 0.82). If the monometer liquid has a specific gravity of 0.85, determine the pressure in the pipe (in kPa and meters of water). %3D Air 66 cm 58 cm Manometer liquid Oil Figure P2.4.7 下

2.4.7. An open manometer, shown in Figure P2.4.7, is installed to measure pressure in a pipeline carrying oil (S.G. = 0.82). If the monometer liquid has a specific gravity of 0.85, determine the pressure in the pipe (in kPa and meters of water). %3D Air 66 cm 58 cm Manometer liquid Oil Figure P2.4.7 下

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized aire in the tank. a.) Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. b.) What gage pressure in p1 in kPa, is needed to provide the given flow rate?
Q2) Calculate the value of pressure ∆p onside the rain water droplet , if we knowthe radius R=0.2mm and the surface tensionδ = 0.074 N/M
Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 = 0.8335 m/s z2 = 0 m Head loss from point 1 to 2 = 0.262 m Find the pressure at point 2
In a vertical pipe conveying oil of specific gravity 0.8, two pressure gauges have been installed at A and B where the diametres are 16 cm and 8 cm respectively. A is 2 metres above B. The pressure gauge readings have shown that the pressure at B is greater than A by 0.981 N/cm2. Neglecting all losses, calculate the flow rate. If the gauges at A and B are replaced by tubes filled with the same liquid and connected to a U-tube containing mercury, calculate the difference of level of mercury in the two limbs of the U-tube.Image attached.
A right circular cylindrical tank container, 2m in diameter and 4m high is 1/2 full of water. When rotated about its vertical axis at the rate of 60 rpm:A.) How many meters will the water surface drop at the center of the vessel? B.) What is the pressure, in kPa, at the base of the container along the perimeter? C.) What is the volume, in m^3, of the paraboloid formed by the rotation of the vessel? (Show complete solution)
Compute the pressure drop in kPa per km of a horizontal 600 mm diam. steel pipe carrying 450 liters/sec of a heavy fuel oil having a sp.gr. of 0.80. Friction factor f = 0.018.
In the figure shown, water (ν = 1 x 10-6 m2/s) flows at a rate of 5 L/s on a system of pipes. There are 40 m of 50-mm diameter pipe, 22 m of 150-mm diameter pipe, and 45 m of 75-mm diameter pipe, all cast-iron. There are two 90o elbows and an open globe valve. If the exit elevation is zero, determine the following:a) friction loss on each pipeb) total minor loss from the surface of the reservoir to the exitc) head extracted by the turbined) mechanical power extracted by the turbine
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference ?????? ?????−???? ?????= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
A slurry behaving as a pseudoplastic fluid is flowing through a smooth round tube having an inside diameter of 5 cm at an average velocity of 8.5 m/s. The density of the slurry is 900 kg/m3 and its flow index and consistency index are n=0.3 and k=3.0Ns0.3/m2. Calculate the pressure drop for 50 m length of vertical pipe with the flow moving against gravity.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
1. A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower end while 1.2 meters at the higher end. The rate of flow through pipe is 5400 liters/min. Find the pressure at the lower end if the pressure at higher end is 68.07 kPa. Neglect losses.
an open circular vessel is 1m in diameter and 2m height. it contains water filled to a depth of 1.5m. if the cylinder rotates about its vertical axis, what is the pressure intensity at the corner of the bottom if w= 6 radians/second Unit of the correct answer: kPa