2.43.The distribution of stress in an aluminum machine component is given (in megapascals) by = y+ 222, "xy = 322 , =x+z, 'yz = x? 0, = 3x+ y, "xz = 2y Calculate the state of strain of a point positioned at (1, 2, 4). Use E = 70 GPa and v = 0.3. 2.44. The distribution

2.43.The distribution of stress in an aluminum machine component is given (in megapascals) by = y+ 222, "xy = 322 , =x+z, 'yz = x? 0, = 3x+ y, "xz = 2y Calculate the state of strain of a point positioned at (1, 2, 4). Use E = 70 GPa and v = 0.3. 2.44. The distribution

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: At a point on the surface of a generator shaft the stresses are as shown in Figure Q2 below.…

A: Given data Compressive load Tensile load Shear stress Angle of inclination of plane in…

Q: Q2/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the…

A: Given data σx = 100 MPa σy = 700 MPa τxy = -400 MPa

Q: 650 600 550 500 450 400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016…

A: Given DataDiameter of bar = 8 mmGauge length of bar = 100 mm

Q: An element is acted by plane stresses as shown in the figure. Calculate: a) Normal and shearing…

Q: Figure Q1 shows a stress state element in a material component. Analyse the element and calculate…

A: Principal Stresses are given by, σ1,2=σx+σy2±σx-σy22+τxy2 tan…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: The principal strains in a plane, measured cxperimentally, are c 630u and 6) 350u. It this is a case…

Q: /B/ A material has the stress-strain behavior shown in Figure. What is the yield strength, and…

A: The yield strength is defined as “the stress at which the material begins undergo plastic…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: The given figure is shown below:

Q: The state of stress at a point is shown with respect to the xy-axes. Determine the equivalent state…

A: step 1-

Q: 650 600 550 500 450 400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016…

A: Stress loading and stress and strain relationship is given in the question and it has been asked to…

Q: A rectangle of an elastic material is deformed in the x, y plane as represented by the dashed lines.…

A: Given: E=300 MPa and poisson ratio μ=0.4No deformation in Z directiona Normal strain strain in x…

Q: A cylindrical bar shown in the figure below has axial loads applied as illustrated. Calculate the…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: in this question a mohar circle is given and we are asked about various segment of a stress diagram…

Q: 1.14 The stress-strain relation shown in Figure P1.14 was obtained during the ten- sile test of an…

A: The given stress-strain relationship of aluminum alloy

Q: PROBLEM 4: An originally rectangular rubber piece is deformed into the shape given by the dashed…

Q: 1) A circular aluminum tube of length L = 400 mm is loaded in compression by forces P (see figure).…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: The plates in the figure below are each 3 inches by 0.5 inches in cross section. If the hole in each…

A: Solution:- Given information: Cross section of plate =3×0.5 in Hole diameter, d=1316 in, and Load,…

Q: The state of plane stress at a point is shown in Figure 1. By using Stress Transformation Formula,…

Q: For the punching operation shown in the figure, compute the shear stress (in GPa) in the material if…

Q: View Policies Show Attempt History Current Attempt in Progress The strain components Ex, Ey, and Yxy…

Q: The state of stress at a point, for a body in plane stress, is shown in the figure below. If the…

Q: A tension test performed on a metal specimen to fracture produced the stress– strain relationship…

A: The given figure is shown below:

Q: Q. No .3 On the free surface of an aluminum [E = 10,000 ksi; v = 0.33] component, the strain rosette…

A: εn =1/2(εx + εy) +1/2(εx – εy) cos 2θ +γxySin 2θ/2

Q: The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain.…

Q: The strains on the surface of an experimental device made of steel (E = 200 GPa and v= 0.33) and…

A: We are required to find the stress along X-direction in MPa

Q: The stress-strain relationship shown in Figure P1.13 was obtained during the tensile test of an…

Q: 35 MPa 14.6 ksi 25 MPa 9.3 ksi 75° 650 7.4 ksi FIGURE P12.7 FIGURE P12.8

A: Given Details:

Q: A Plane stress state is given on a material element as shown below. O=a+b+h (MPa), Oz=b+c+d+h (MPa),…

Q: A circular rod and a 3/8-in.-thick rectangular bar are both made of a plastic material that has an…

A: Required Change in the diameter of the Circular Rod

Q: 1- Consider the unit cube shown in the Figure, which undergoes the deformation: 1 x₁ = α (X₁ — —…

A: Deformation : The change in size or shape of an object is referred to as deformation. The absolute…

Q: 10.Stress transformation. From the figure below, find the orientation of the maximum principal…

A: Given:- σx=50 MPaσy=-10 MPaτxy=40 MPa To find:- Direction of maximum principal stress Magnitude of…

Q: τ || ây = E7 = At this point, determine the strain components Εχ, Ey, Ez, and xy. Assume that E = 72…

Q: Problems: Stress (ksi) 53.2 1. Determine the ductility (u) of the material based on the stress-…

Q: A tension test performed on a metal specimen to fracture produced the stress-strain relationship…

Q: Question 3 For the state of plane stress shown in Figure Q2, (a) construct Mohr's circle (b)…

A: To find Principal stresses and planes

Q: Question 7 Given an element with stresses as indicated in the figure, answer the following…

Q: Problem 1: Given is a brass bar assembly as shown in the figure, evaluate the average normal stress…

Q: A machine component is subjected to a load of P = 3,800 N. Which stress element represents the state…

A: Stress element: The elements which are generally used to represent the stresses acting at a point on…

Q: The state of stress at a point is shown with respect to the xy-axes. Determine the equivalent state…

Q: Based in the table 1. 1) Develop a best-fit equation for the relationship between stress and strain.…

A: As per rules I have to answer first 3 sub parts

Q: 320 MPa 12.5 ksi 55 50° 190 MPa 21.0 ksi FIGURE P12.3 FIGURE P12.4

A: Given Details

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: Two bars are made from different materials namely Material X and Material Y. Each sample has an…

A: Material X = Ductile material like mild steel Material Y = Brittle material like concrete Brittle…

Q: The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and…

A: Answer We can use Torsion equation for the calculation of shearing stress and Angle of twist in…

Q: The stresses acting on an element is given in figure. a.Calculate the following parameters of Mohr…

Q: strain components &n, Et, and Ynt at the point if the n-t axes are rotated with respect to the x-y…

Q: Problem (7,2): The surface of an airplane wing is subjected to plane stress with normal stresses a,…

Q: Required information Consider the given state of stress. Given: X= 40 MPa and Y= 60 MPa. 25 MPa X…

A: Solution; Given that; σx=-40 MPaσy=60 MPaτxy=25 MPaFor plotting Mohr's circle,Coordinates of point…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

i need the answer quickly

2.43.The distribution of stress in an aluminum machine component is given (in megapascals) by
o, = y + 2z?,
"xy = 3z2
'yz = x?
o, = 3x + y,
"xz = 2y
Calculate the state of strain of a point positioned at (1, 2, 4). Use E = 70 GPa and v = 0.3.
2.44.The distribution of stress in a structural member is given (in megapascals) hy Fas (d)of
Windows

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A cylindrical rod AB has a length ? = 80 cm and a diameterof ? = 2 cm. The modulus of elasticity is ? = 200 GPa andyield strength is ?? = 300 MPa. The stress-strain diagram ofthe rod is shown in the left figure. A force ? = 100 kN isapplied to the bar and then fully removed (right figure).Determine the permanent set in the rod.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. where P=25 .
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
Based in the table 1.1) Develop a best-fit equation for the relationship between stress and strain. Employ Naïve–Gauss elimination method whenever necessary.S=______+______e + _______e2 2) Determine the coefficient of determination for the equation. R2 =_______ 3) Calculate the stress value to the most accurate value at strain value 0.53.s = _______Pa4) The yield point is the point on a stress–strain curve that indicates the limit of elastic behaviour and the beginning of plastic behavior. In this case, the yield point occurs at a stress value of 80. Determine the corresponding strain value at the yield point. In any relevant method, use a stopping criterion of 0.05% e =_______ 5) The ultimate strength is the maximum point on the stress–strain curve. This corresponds to the maximum stress that can be sustained by a structure in tension. Compute the ultimate strength point of the polymeric material (strain value that gives maximum stress). In any relevant method, use a stopping…
Steel cylinder has 200 mm mean diameter with a wall 1 mm thick and 310 mm long. Determine the circumferential and longitudinal stresses that occur on the cylinder if the maximum pressure difference allowed between the inside and outside must not exceed 100 MPa. Determine the effects of three dimensional loading by determine volumetric strain and change in volume for the first steel cylinder. Modulus of elasticity E= (210 GPa), Poisson's ratio 0.30. 7
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 100 MPa, σy=σy= 20 MPa, and τxy=τx⁢y= 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 68 GPa and v = 0.32 for the machine component.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa
A tension test performed on a metal specimen to fracture produced the stress– strain relationship shown in Figure P1.14. Graphically determine the following (show units and all work): a. Modulus of elasticity within the linear portion. b. Yield stress at an offset strain of 0.002 m/m. c. Yield stress at an extension strain of 0.005 m/m. d. Secant modulus at a stress of 525 MPa. e. Tangent modulus at a stress of 525 MPa.
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
For P = 100 MPa, determine the range of values of τxy for which the maximum tensile stress is equal to or less than 60 MPa. (Round the final answer to one decimal place.)