2.47 The rigid block of mass M is supported by the three symmetrically placed L1om-l-1.0 m-- M rods. The ends of the rods were level before the block was attached. Determine the largest allowable value of M if the properties of the rods are as listed (a, is the working stress): E (GPa) A (mm?) o, (MPa) Сорer 120 900 70 Steel 200 1200 140 -1.0 m→l-1.0 m- 160 mm Steel 240 mm 160 mm

2.47 The rigid block of mass M is supported by the three symmetrically placed L1om-l-1.0 m-- M rods. The ends of the rods were level before the block was attached. Determine the largest allowable value of M if the properties of the rods are as listed (a, is the working stress): E (GPa) A (mm?) o, (MPa) Сорer 120 900 70 Steel 200 1200 140 -1.0 m→l-1.0 m- 160 mm Steel 240 mm 160 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 90-kg smooth circular cylinder A with a radius of 0.6 m is held in equilibrium by a cord CD and a bar BC of negligible mass. The length of bar BC is 2.4 m. a. Draw the FBD of the circular cylinder and the bar BC.b. Determine the tension in the cord CD.
The lever must exert a force of P = 2200 lbs at B as shown. The lever lengths are a = 8 in. and b = 41 in. The allowable bending stress for the lever is 12100 psi. If the lever height h is to be 3.0 times the lever thickness t (i.e., h/t = 3.0), what is the minimum thickness t that can be used for the lever? Use equilibrium to calculate the magnitude of load Q.
A 100- m steel tape is used to measure the distance of the line and found to be 1539.28- m long. During measurement, the tape is supported at the ends under a pull of 10- kgs and the observed mean temperature is 31°C. The tape is of standard length at 20 °C and a tension of 12- kgs. Thecross sectional area of the tape is 0.035 cm2. The coefficient of linear expansion is 0.0000116/°C and the modulus of elasticity of steel is 2.0 (10)^6 kg/ cm2. The tape weight is equal to 1.5- kg. a) Determine the total correction for temperature.b) Determine the total correction due to tension.c) Determine the total correction due to sag.d) What is the correct length of a line?
The system lamp has a mass M and is supported by the six strings shown. The length of the chords and the horizontal distance ED are constant, point E remains fixed but the vertical distance ED can vary. a) If in the position shown the chord BC is horizontal, calculate the angle ? to maintain equilibrium, consider the mass M = 10 kg. b) Explain what happens to the magnitude of the stresses when point D moves.
The50-lb homogeneous bar AB is suspended from a rope that runs over a small peg at C. The bar is kept in the position shown by the horizontal force P. Determine the smallest coefficient of static friction at C for which the bar will be at rest. C
a.) value of d due to shear b.) accepted value of d
STRENGTH OF MATERIALS (NO LONG EXPLANATION NEEDED) PLEASE WITH FBD! RATE WILL BE GIVEN For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to load P = 40 kN. The rods are identical except for their lengths. Find the (a) stress in rod A if its cross-sectional is 300mm2 (b) If rod A elongates by 2mm, how much is the elongation of rod B?
A 600 kg material is hung from the end of the horizontal bar BD as shown. Determine the stress on the rod AC if its diameter is 30 mm. Use 2 decimal places in every solved values. Pls include fbd.
The springs BA and BC each have a stiffness of 500 N/m and an unstretched length of 3 m. Determine the horizontal force F applied to the cord which is attached to the small ring B so that the displacement of AB from thewall is d = 1.5 m.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. Answer in 1 decimal place
Solve q4 a and b both parts plz solve this in maximum one hour if u can't solve this u can reject in half hour so that i can't wait of your answer plz..
Solve for: Ax, Ay, Dy, Bx, By, MB, Cx, Cy, MC (complete solution)