2.An inductor L, is connected in series with a parallel combination of inductor L2 and capacitor C. The impedance of the circuit at w = 400 rad/sec is j100. The circuit is to yield infinite impedance at w = 1000 rad/sec and zero impedance at w = 2000 rad/sec. Solve for L1, L2 and C.

2.An inductor L, is connected in series with a parallel combination of inductor L2 and capacitor C. The impedance of the circuit at w = 400 rad/sec is j100. The circuit is to yield infinite impedance at w = 1000 rad/sec and zero impedance at w = 2000 rad/sec. Solve for L1, L2 and C.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Let Zeq be the equivalent impedance of a parallel connection of an inductor with inductance L and a…

Q: Q2) For the circuit in the figure, the capacitance is 0.5, the resistor is linear with v-i…

A: It is given that the resistance has a linear characteristic v=2i. So we have vi=2. And by ohm's law…

Q: 6. Find the characteristic impedance expression in terms of the inductance and capacitance…

A: In this question, We need to choose the correct options What is characteristics impedance of the…

Q: Q Find the capacitance C necessary to improve the power factor to 0.95 lagging in the circuit shown…

A: Z = 20∠30°Z = 20(Cos 30°+j Sin 30°)Z = 20 32+j2Z = 103+j 10ΩBoth branches are parallel,Total…

Q: Q2:- A capacitor of resistance 20 Q and capacitance 0.5 µf is connected in parallel with a coil of…

Q: Consider the following circuit consisting of an AC generator V-V.sin(et), a capacitor C, an inductor…

A: Given circuit diagram is shown below. Here the AC generator is V=Vosinωt Volts. We need to find the…

Q: Write MATLAB program to define the exponentially varying sinusoid f(t) mentioned in topic 4.3. Also,…

A: The given signal is Create a MATLAB script, and write the code given below. Then RUN it.

Q: d. Calculate the reactance, XL2 , of the inductor, L2 e. Calculate the reactance, XC , of the…

A: In this question, We need to determine the inductive Reactance, Capacitive Reactance as shown in…

Q: *P5.33. A voltage vL(t) = 10 cos(2000rt) is applied to a 100-mH inductance. Find the complex…

Q: For the circui find the frequency (in radiansper second) at which the impedance Zab is purely…

A: Assume the frequency ω, For purely resistive put imaginary term equals to zero,

Q: Determine the capacitance and voltages

Q: Q13 A variable capacitance and a resistance of 290 2 are connected in series across a 110-V; 60-Hz…

A: In this question, A resistance R= 290 ohm and capacitance C(6uF -32uF) are connected to the voltage…

Q: An AC bridge is supplied with a source of 10 kHz as shown in figure 1. If Z, is a paralle…

A: An AC bridge circuit is used for measuring quantities like resistance, inductance, capacitance in a…

Q: Design a single circuit element containing one inductor, one capacitor and one resistor with v(t) of…

A: Steps: Possibilities of elements are Resistor, Inductor, and Capacitor Since voltage contains a dc…

Q: A circuit supplied by 8V, 50HZ, is shown in Figure C5 below, is used to find the unknown value of…

Q: Exacise Find Lislor La1) for the cicnits ftra

A: (a) So, So, the flux will be: ϕ12=∫y=dd+b∫x=2btanα0dϕ where dϕ=dB.A=B.dA=μoI12πydxdy…

Q: Consider an inductor whose inductance varies as L(x) 0.25H/cm-z, where is the variable length of the…

Q: A resistance R, capacitance C, and inductance L are connected in series to a voltage source with…

A: Note: As per the policy we can solve only 3 sub parts of a question, please re-upload the remaining…

Q: Q Find the capacitance C necessary to improve the power factor to 0.95 lagging in the circuit shown…

Q: For the given circuit, (a) what is the inductance and (b) the solution form of V5(t)?

A: The given circuit and the waveform is as shown below,

Q: The circuit shown in Figure having resistor 130 Q and a capacitor 50 µF is connected to a 210 V, 50…

A: We need to solve given RC circuit.

Q: Explain the key advantages of complex sinusoids when compared to real sinusoids and their respective…

A: For its real portion, a Complex sinusoid has an "in-phase" component, and for its imaginary part, it…

Q: A source provides a sinusoidal current i,(t) of 60 Hz to two resistors and a capacitor, so that…

Q: a) Find the equivalent impedance for the combination of the three circuit elements expressed as a…

A: As per the guidelines of Bartley we solve first three subpart.

Q: Q2) Assuming a sinusoidal source and a uniform load current, analyze the circuit because and draw…

A: We will get VinN/N2 = A sin(ω.t) (2) Iout = VoutR

Q: (c) Given a 50nF capacitor, calculate a suitable value of R to realise an RC LPF with a roll-off…

Q: Problem 4: Derive an expression for the equivalent inductance for the circuit shown in Figure below:…

A: The circuit diagram is shown below: Applying Kirchoff's voltage law(K.V.L) in the above circuit,…

Q: Consider the circuit in Figure Q.1(b). The frequency of the circuit is given 23 f = 50 Hz. Find: (i)…

A: The reactance of inductance and capacitance is given by Inductive reactance, XL = 2πfL Capacitive…

Q: Here, the circuit in figur 5 is to be examined. v(t) = 32Vcos(10000t+0°) a) Find the impedance…

A: In this question, Resistance R, inductance and capacitance C are connect as shown in the circuit.…

Q: 2. A sinusoidal e.m.f. 110 sin 400t volts is connected in series in a circuit with an inductance of…

Q: Let Zeq be the equivalent impedance of a series connection of an inductor with inductance L and a…

Q: (b) Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to…

A: Capacitor- capacitors are widely used in electronic circuits to block direct current power while…

Q: Find an expresson For ilt) in the RC circut when voltage,v(t), is applied at t0. Consider he…

A: In this question, Find the value of current I(t) . Capacitor act as open circuit after long time.

Q: Assuming that a nonzero ac voltage source is applied, what can you say about whether the power and…

A: Draw the circuit diagram for a series connection of the inductor and the capacitor.

Q: 1. For an ideal capacitor, the impedance has __________. (Choose one) Group of answer choices - no…

Q: Consider the circuit shown in Figure P5.79. Find the phasor current I. Find the power, reactive…

A: To find the value of current I the circuit can be modified as The value of Z is given as Thus…

Q: *P5.33. A voltage VL(t)=10 cos(2000TTt) is applied to a 100-mH inductance. Find the complex…

A: Key Points Let voltage across the inductance is taken as a reference then current in the inductor…

Q: expression for the voltage across a 2 µF capacitor is given below. what is the sinusoidal expression…

A: We know relationship between voltage and current for capacitor.

Q: A voltage source is supplying a load through a long cable. The load is consuming 250 VA at 0.82…

Q: A pure inductance of L = 144 mH is connected to a V = 112 V, 50 Hz supply. The current ta by the…

Q: the parallel connection of a resistor and a capacitor takes 0.6 A rms from a 120 V rms voltage…

Q: Find the Thevenin equilvent circuit

A: The circuit diagram is:

Q: Write an expression for the complex impedance of a parallel combination of an inductor, L, and a…

A: It is Given that:Parallel combination inductor (L) and capacitor(t).

Q: 5. At what frequency will a 200-µH inductance have a reactance of 20 2? How much current will flow a…

Q: A Calcalate the value of the Capaeitance at if w=So0D rad/see resanamee

A: In the network, Inductance , capacitance and resistance Resonance frequency w= 5000rad/s Find the…

Q: An inductor L1 is connected in series with a parallel combination of inductor L2 and capacitor C.…

A: In this circuit we discuss about the LC circuit.

Q: A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a…

Q: A RLC circuit with 100 Q resistor R1, 3 mH inductor L1, and 5 µF capacitor C1 are connected in…

A: The solution is given below

Q: Exercise 2: A voltage vc(t)=100cos(200t) is applied to a 100 µF capacitance. (a)Find the impedance…

Question

2.An inductor L, is connected in series with a
parallel combination of inductor L2 and
capacitor C. The impedance of the circuit at
w = 400 rad/sec is j100. The circuit is to yield
infinite impedance at w = 1000 rad/sec and
zero impedance at w = 2000 rad/sec. Solve
for L1, L2 and C.
W =

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An inductor L1 is connected in series with a parallel combination of inductor L2 and capacitor C. The impedance of the circuit with ω = 400 rad/s is j100 Ω. The circuit is to yield infinite impedance at ω = 1000 rad/s and zero impedance at ω = 2000 rad/s. Determine the value of capacitance of the capacitor C.4.
The total impedance Z, of a circuit containung an inductor with inductance L and resistance R in series is given by Z  R  j2fL where f  frequency . If Z  (50  j200)ohm and f = 50Hz. Find R and L
Show that at a given frequency ω, the circuits will have the same impedance between the terminals a,b ifR1=R21+ω2R22C22,C1=1+ω2R22C22ω2R22C2.2. Find the values of resistance and capacitance that when connectedin series will have the same impedance at 40 krad/s as that of a1000 Ω resistor connected in parallel with a 50 nF capacitor.
1. For an ideal capacitor, the impedance has __________. (Choose one) Group of answer choices - no real component and a positive reactive component - no real and no reactive components - negative real component and no active component - positive real component and no reactive component - no real component and a negative reactive component 2. Select the response that best describes the phase relationship between v1(t) and i1(t). (Choose one) v1(t) = 7cos(100t-π/6)i1(t) = 3cos(100t+π/2) Group of answer choices - v1(t) is in phase with i1(t) - v1(t) is leading i1(t) by π/6 - v1(t) is leading i1(t) by 3π/6 - i1(t) is leading v1(t) by 3π/6 - i1(t) is leading v1(t) by 2π/6 - v1(t) is leading i1(t) by 4π/6 - i1(t) is leading v1(t) by 4π/6 - i1(t) is leading v1(t) by π/6 - v1(t) is leading i1(t) by 2π/6
An RLC series circuit has an impedance of 60 Ω and a power factor of 0.50, with the voltage lagging the current. (a) Should a capacitor or an inductor be placed in series with the elements to raise the power factor of the circuit?(b) What is the value of the capacitance or self-inductance that will raise the power factor to unity?
When the average real power absorbed by an impedance is zero, then the impedance is: Select one: a. A parallel combination of resistors and capacitors b. An ideal resistor c. A pure inductor d. A resistor in parallel to an inductor e. A resistor in parallel to a capacitor
A capacitor branch having a ratio of xC to RC of 5 ohms is paralleled with an impedance consisting of a 4 ohms resistance and a 3 ohms inductive reactance. The power factor of the resulting current is 0.8 leading. Find the capacitive reactance and the size of the capacitor if micro-farad if the frequency is 60 Hz. Also, find the total impedance of the circuit.
A 20 Ω resistor is connected in parallel with a 5 mH inductor. Thisparallel combination is connected in series with a 5 Ω resistor and a25 μF capacitor.1. Calculate the impedance of this interconnection if the frequency is2 krad/s.2. Repeat (a) for a frequency of 8 krad/s.3. At what finite frequency does the impedance of the interconnectionbecome purely resistive?4. What is the impedance at the frequency found in (c)?
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage VR and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60Hz , R = 10 ohm Vcoil = 22.4 V. VR = 20 V and v = 36v , find the resistance and inductance of the coil.
Consider the voltage v(t)= 40sin(100πt+140 o ) V. a) Find the period of this voltage in millisecond and the voltage value at t=6 ms. b) This voltage is applied to the circuit below. Find VR , VC and VL phasors and and draw them on the realimaginary axis. Find vR(t) , vC(t) and vL(t) via inverse phasor, comment phase angles. c) Find active, reactive and complex power (P,Q,S) on the inductor.
1. Calculate the total impedance of the circuits in Fig. Express your answer inrectangular and polar forms. (a) ZT Rectangluar form -> ZT = 6.8 + 8.2j Polar form -> ZT = 10.65Ω∠50.33° (b) ZT Rectangluar form -> ZT = 12 - 6j Polar form -> ZT = 13.42Ω∠-26.57° (a) ZT Rectangluar form -> ZT = 5k + 10kj Polar form -> ZT = 5kΩ∠63.43° I manage to answer the parts of the first question can you check if my answer is correct?
A sinusoidal 50 Hz voltage of 200 V (rms) supplies the following three circuits which are inparallel: (a) a coil of inductance 0.03 H and resistance of 3 ohms, (b) a capacitor of 400 microFaradin series with a resistance of 100 ohms and (c) a coil of inductance 0.02 H and resistance 7 ohms inseries with a 300 microFarad capacitor. Find the total current supplied?