The simple truss is loaded by a system of forcesas shown in the figure. The truss is supported bya pin at A and a roller at E. If P1 = 40 [KN] and P2= 20 [KN], then the force developed in themember (ED) is.%3DBCD2 mAGF-1.5 m-F1.5 m--1.5 m--1.5 mP2Select one:a. 51.78 kN - Tensionb. 78.15 kN - Compressionc. 17.85 kN - Tensiond. 31.25 kN - Compression

Answered: Image /qna-images/answer/89b13c93-2c6e-4f1c-a827-d3b68c764dd3.jpg

Answered: 20 [KN], then the force developed in…

Engineering

Mechanical Engineering

20 [KN], then the force developed in the member (ED) is.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
Question #3: In the figure below, a 100 N weight flower pot is suspended by three ropes. The tension in rope AB is three times the tension in ropes AC and AD. Find the dimension “d” on the figure which corresponds to the z-coordinate of point B. Also find the tensions in ropes AB, AC, and AD. Please do each step as I am trying to check my answers. I got to the point of setting the ijk components equal to zero. I'm stuck at multiplying the tension in vector AB times 3.
The load on a 2-in.-diameter hydraulic cylinder increases from 10,000 lb to 15,000 lb. Due to the compressibility of the oil, the piston retracts 0.1 in. If the volume of oil under compression is 10 in^3, what is the bulk modulus of the oil in units of kpsi? Enter only a whole number.
what's mean below sentence? i couldn't understand θm=θ1-θ2lnθ1θ2=Thi-Tco-Tho-TcilnThi-TcoTho-Tci=60-55-30-20ln60-5530-20=7.2135 °C
The stress state within the lateral wall of a soda can is approximated as shown. p is the internal pressure, r is the radius of the can, t is the wall thickness. Express the stress state shown in a matrix, where the only two non-zero stress components are σxx and σyy, all other stress compoenents are zero. Express the equivalent stress σe associated with the stress state shown in terms of p, r, and t.
The mechanism shown in the figure controls the lifter. Calculate the reactions on CDE as the weight supported by the platform is W W(N)= 2800, L1(m)=0.6, L2(m)=0.6 , L3(m)=0.2 1) For three dimensional problems, please use vector notation.2) State what all the transactions you have done. All intermediate actions you have to doshow clearly.3) Please write the units next to the values you find.4) In the related questions, please draw the free body diagram.
A) Imagine a procedure used for the execution of a certain work, as shown in the following figure. Such a crane has a mass of 1000 kg and is transporting a coffin with a total mass of 2400 kg. Assume that support A is fixed, support B is movable, and point G is the center of gravity of the lift. What are the support responses in kN? Question 1 options: a) The support responses are as follows: Rax = Rbx = 34 kN and Ray = 109.33 kN. b) The supporting responses are as follows: Rax = Ray = 109.33 kN and Rbx = 34 kN. c) The support responses are as follows: Rax = 56.8 kN; Rbx = 109.33 kN and Radius = 34 kN. d) The support responses are as follows: Rax = 156.7 kN; Rbx = 89.65 kN and Radius = 34 kN. e) The supporting responses are as follows: Rax = Rbx = 109.33 kN and Ray = 34 kN. B. Consider the beam shown in the following figure. In this beam, there are different types of existing forces, such as applied moment, distributed load and point load. Knowing the magnitude of each of the forces,…
In the United States, electricity is sold using the SI units of kilowatt (kW) or megawatt (MW), and fuel for power generation stations is generally purchased using English units, e.g., British thermal unit (Btu), gallon (gal), and ton. An industrial power plant has an average annual load of 100 MW (electrical). If the overall thermal efficiency is 33% (based on HHV), what is the annual cost of fuel if the plant is fired with (a) natural gas, (b) No. 2 fuel oil, and (c) bituminous coal? Use the data from Tables 2.2, 2.7, and 2.13. Assume the cost of natural gas is $5/million Btu, the cost of No. 2 fuel oil is $3/gal, and the cost of bituminous coal is $60/ton (1 ton = 2000 lbm)
In the piezometer in the figure, liquids stands 6.10 ft. above m. what is the pressure at m in pounds per square inch if the liquids is : a)water b) oil (sg. 0.80) c) mercury d)molasses ( sp. gr. 1.50) What is the pressure head in inches of each liquid?
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?
In the arrangement shown in the figure, a cable is attached to the end of a cantilever beam. We will model the cable as a rod. Denote the translational spring constant of the beam by kb and the translational spring constant of the cable by kc. The displacement x is caused by the applied force f. What is the equivalent spring constant for this arrangement?
Find the magnitude of tension in string (or spring scale reading) and the magnitude of vertical FV and horizontal FH components of force applied on meter stick by the hinge. (Project this equation on Ox …this will give you the magnitude of FH force. Project this equation on Oy …this will give you the magnitude of FV force) (Draw a free body diagram) please data: Lruler = 1m mruler= 134 g dstring=80 cm d1= 35 cm d2= 82 cm M1=250g M2=150g θ = 38 degrees α= 62 degrees