21. In a repair shop compressed air is used to operate pneumatic tools. The total length of the airline including all the loss coefficients in terms of equivalent air is about 500 ft. The airline consists of smooth pipe of I.D. = 0.5 inch. The com- pressed air is cooled to 75 F when entering the line. A pneumatic tool requires 35 psia of compressed air to operate. To what pressure should the air be pressurized by a compressor to provide the desired pressure for the tool? What power is required to obtain such pressure if the compression process can be assumed isentropic? Air ve- looity ot the inlet ic 10 &le

21. In a repair shop compressed air is used to operate pneumatic tools. The total length of the airline including all the loss coefficients in terms of equivalent air is about 500 ft. The airline consists of smooth pipe of I.D. = 0.5 inch. The com- pressed air is cooled to 75 F when entering the line. A pneumatic tool requires 35 psia of compressed air to operate. To what pressure should the air be pressurized by a compressor to provide the desired pressure for the tool? What power is required to obtain such pressure if the compression process can be assumed isentropic? Air ve- looity ot the inlet ic 10 &le

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir height=220ft length of pipe= 1500ft final aubdivisiion= 24ft, 20psi 1)determine the normal pipe size 2) if the pipe size is not avalible what size combination will work 3) if we used a 8 inch pipe determine the min thickness 4)determine the max pressure that can deelope in the 8in system
A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the diagram of a process control that controls the hot water flow Q? and the cold water flow Q? to adjust the water temperature as the machine user specify? and define each block? Note: pressure controlled pneumatic actuator is used as a valve.
A compressor delivers 2000 cfm of air through a pipe at a receiver pressure of 140 psig. What minimum size schedule 40 pipe should be used if the pressure loss is to be limited to 0.10 psi per foot of pipe length?
Industrial pipes Do the stops allow movement in a certain direction, but only for a certain distance?
A self-priming centrifugal pump is used to pump water at 25°C from a reservoir whose surface is 2.2 m below the centerline of the pump inlet. The pipe is PVC pipe with an ID of 26.0 mm and negligible average inner roughness height. The pipe length from the submerged pipe inlet to the pump inlet is 2.8 m. There are only two minor losses in the piping system from the pipe inlet to the pump inlet: a sharp-edged reentrant inlet (KL = 0.85), and a flanged smooth 90° regular elbow (KL = 0.3). The pump’s required net positive suction head is provided by the manufacturer as a curve fit: NPSHrequired = 2.2 m + [0.0013 m/(Lpm)2 ]V.2 , where volume flow rate is in Lpm. Estimate the maximum volume flow rate (in units of Lpm) that can be pumped without cavitation.
Water at 83 L/sec is flowing inside a 6-inch schedule 40 nominal pipe. Determine the following.a) What is the Reynold’s number of the water?b) What is the maximum velocity in ft/sec of the water at room temperature in the pipe?c) What is the pressure drop reading in mmHg of a pitot tube inserted in the pipe? (The fluid inside the pitot tube is mercury.) Assume a viscosity of 0.001 Pa*s and density of 1000 kg/m3.
. What horsepower is supplied to air moving at 7m/min through a 70cmx90cm duct under a pressure of8cm of H2O?
The figure 1 above presents a crudely simplified centralised water heating system. The system comprises of two heating lines, the first line having one radiatorand the second has four radiators in series.The pressure after the pump (point (1)) is 2 bar, and the flow velocity is 1.2 m/s. For simplicity we can assume the water to be in constant temperature of 60◦C. Loss coefficients and pressure losses are listed in Table 1, and pipe lengths and diameters are given in Table 2.For the system balancing, the target is to divide the mass flow so, so that 20% of the mass flow goes to the first line (i.e. through radiator R1.1) and 80% of the flow goes to the second line (R2.1 - R2.4):(a) How large pressure loss is needed in the control valve CV1 to get the desired flow rates in the two lines? (b) How large is then the minor loss coefficient of the said valve, KCV1? (c) How much is the pressure, in bar, at the end of the line at section 4?
6 m^3/min of 15.6°C SAE 30 is to be pumped from a tank through 40 meters of horizontal pipe; the oil will exit the pipe to the atmosphere. The pump’s push on the oil can create a gage pressure of 38.7 kPa at the horizontal pipe inlet. What minimum pipe diameter should be selected?
A 6-nominal schedule 80 cast iron pipe is 3500 m long. It is to convey octane at a flow rate of 0.02 m3/s. Determinethe pressure drop of the octane.
Water is to be pumped to an atmospheric rooftop storage tank atop a 5-story building, 75 feet above ground-level. A pump station is located at the ground-level. The suction line is a 2-inch ID commercial steel pipe tapped into a municipal supply line maintained at 50 PSIG 5 feet below ground-level. The discharge line is 1.5-inch ID commercial steel, and the total length of pipe is approximately 100 ft. There are two ball valves, a water meter, and gate valve on the discharge line. Determine the pump head required to deliver 40 GPM and the pump power that must be supplied to the water. If a pump is required, what is the motor power required if the pump operates at 55% efficiency?
Question 7. Since the velocity of the fluid passing through the 4 mm diameter pneumatic pipe in the pneumatic system is 200 cm/s; a) What is the flow rate of the compressed air in lt/min? b) Calculate the velocity of the air passing through 6 mm diameter in the same pressure line.