Fundamentals of Surveying between the zero and 30-m marks.23. COMBINED CORRECTIONSs. A line was found to be 2865, 35 mlong when measured with a 30-m tape under a steady pull of6.5 kg at a mean temperature of 30°c. Determine the correctlength of the line if the tape used is of standard lengthat 20°c under a pull of 5.5 kg. Assume the cross-sectionalarea of tape to be 0.025 cm², elastic modulus as 2.10 X 106kg/cm?0.0000116/1°c.and coefficient of thermal expansion to be24. MEASURI NG ANGLES WITH TAPE. The sides of a triangle1063.55, 1840.33, and 1325.05 m. Determine themeasurethree angles in the triangle.25.. OBSTRUCTED DISTANCES. In the accompanying sketch it isrequired to determine the distance between points A and Bwhich spans à wide and deep river. Lines BD and CE, whichmeasure385.75 m and 529.05 m,respectively, are estab-|lished perpendicular to line ABC. i£ points D and E arelined 'up with A and the length of BC=210.38 m, determinethe required distance.90 22. COMBINED CORRECTIONS. A 30-m tape weighs 12.5 g/m andhasa cross section of 0:022 cm2. It measures correctlywhen supported throughout under a tension of 8.0 kg and ata temperature of 20 °c. When used in the field, the tape isonly supported at its ends, under a pull of 9.0 kg, end ataveragetemperature of 28°c. Determineanthedistance

Note : As per the bartleby guidelines the problem comes under multiple question's.Therefore solution…

23. COMBINED CORRECTIONS. A line was found to be 2865, 35 long when measured with a 30-m tape under a steady pull1 6.5 kg at a mean temperature of 30°c. Determine the corre length of the line if the tape used is of standard leng at 20°c under a pull of 5.5 kg. area of tape to be 0.025 cm², kg/cm? 0.0000116/1°c. Assume the cross-section elastic modulus as 2.10 X 1 thermal expansion and coefficient of to

23. COMBINED CORRECTIONS. A line was found to be 2865, 35 long when measured with a 30-m tape under a steady pull1 6.5 kg at a mean temperature of 30°c. Determine the corre length of the line if the tape used is of standard leng at 20°c under a pull of 5.5 kg. area of tape to be 0.025 cm², kg/cm? 0.0000116/1°c. Assume the cross-section elastic modulus as 2.10 X 1 thermal expansion and coefficient of to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine support reaction. Given a=5 m b=10 m P=30 KN
Calculate Tension BD if P = 100 kN.
A 30 m steel tape was standardized at a temperature of 20°C and under a pull 5 kg. The tape was used in catenary at a temperature 25°C and under a pull of P kg. The cross-sectional area of the tape is 0.02 cm2, its weights per unit length is 22 g/m. Young’s modulus = 2 x 10-6 kg /cm2, α = 11 x 10-6 per °C. Find the correct horizontal distance, if P is equal to (i) 5 kg, and (ii) 11 kg.
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
A uniform 50-kgf board rests on rough supports located at A and B in the figure. Thefriction coefficient μs=0.60 on both contact surfaces. If a man weighing 80 kgfpulls on the rope with a force of 40 kgf, determine:a) The angles "min" minimum and "max" maximum for which the system is in equilibrium.b) The minimum coefficient of friction that must exist between the soles of the man's shoes andthe soil for each of the cases in section a.
Determine the uniform factored load each. Pn=270kN
A reinforced concrete beam has a width of 400mm and an effective depth of 600mm. It is reinforced for tension with 4-28mm rebars. F'c = 20.7MP and Fy = 414.6MPa. 7. Determine the ultimate moment capacity. a 484.76KN.m b. 448.67KN.m 8. Determine the percent increase in ultimate b. 34.4% a. 25.1% c. 487.46KN.m d. 446.87KN.m moment if depth is increase to 700mm. c. 18.98% 15.68%
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
Determine support reaction at B . Given P=100 Kn L=10 m
f’c = 28 fy = 415 Mpa ex= 320mm a. Calculate depth of neutral axis b. Calculate the stress in extreme compression reinforcement in Mpa
pls answer ASAPa.) Find the location of centriod, ȳ, from the top of the beam.b.) Determine the moment of Inertia in mm^4