Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa

Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter7: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 7.2P: A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly...

See similar textbooks

Similar questions

Given the following floor plan of a building as shown in FIGURE ADL= 3.6 kPa, LL = 4.2kPaIf Columns E and H are deleted and beam DEF and GHI rests on beam BEHK. Based on tributary area. 1. Find the load on BEHK at E.a. 140.4 kNb. 266.6 kNc. 210.6 kNd. 152.1 kN2. Find the load on beam BEHK at H.a. 152.1 kNb. 266.6 kNc. 210.6 kNd. 133.7 kN3. Find the maximum moment on beam BEHK. Use Pab²/L². a. 174.4 kNmb. 236.3 kNmc. 273.2 kNmd. 385.8 kNm
A 1.80m x 1.20m x 0.4m footing with a column at the center is loaded with a column at the center is loaded with a column load of 750 kN and a moment of 290 kN-m acting about the transverse axis of the footing base. The base of the footing is 1.25m below the ground. Use the unit weight of 24 kN/m^3 for concrete and 18 kN/m^3 for the soil above the footing.Determine the equivalent eccentricity of the load,mm?Maximum net soil pressure under the footing, kPa?Required minimum additional axial load so that the whole footing base is under pressure,kN?
Given a simply supported reinforced concrete slab with the effective span lo=2.8 m. The slab is 90 mm thick and reinforced by $10@200 longitudinal bars. The material properties are f= 11.9 N/mm², f= 1.6 N/mm². fy=280 N/mm, and E, = 2.0 x 10 N/mm². Calculate the maximum load (per square meter) that the slab can sustain.
What is the equivalent line load that beam B2 will carry from the loads in Area 1? a. 10.6 KN/m b. 21.2 KN/m c. 4.8 KN/m d. 9.6 KN/m What is the equivalent line load that beam B2 will carry from the loads in Area 2? a. 8.85 KN/m b. 23.6 KN/m c. 17.7 KN/m d. 4.5 KN/m What is the total line load that beam B2 will carry a. 19.45 KN/m b. 11.2 KN/m c. 44.8 KN/m d. 9.3 KN/m
What is the equivalent concentrated load of a triangular load which varies from 0 at one support and 9 kN/m at the other support carried by a 6-m simply supported beam? (Answer must be in kN.)
1. A rock anchor 3 1/2” in diameter is placed in rock. The which has an allowable shear strength of 400 psi. Determine the required anchorage length to safely carry a 120 ton load using a 1.5:1 F.S.
In the trapezoidal load shown, if h1 = 4 kN/m, and y = 3 kN/m. What is the value of h2?
A five-storey building is subjected to a windload, computed Vu = 2,350 KN, design the reinforcement of a shear wall that is 5.8m long and 4.2m high, and 250mm thick. F’c= 23.5MPa and fy=275MPa. If the wall is considered to be a load bearing with a concentrated load, Pu= 7,255 KN, can the thickness of wall carry the ultimate axial load, otherwise what is the design wall thickness? Assume . Sketch the rebar details.
A rectangular "Apitong" beam 50mm x 250mm is used as a simply supported beam 3.2m long. Determine the largest uniformly distributed load, which can be, applied over the central half of the beam if the flexural stress is limited to go 12MPa?
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly distributed load of 180 kN/m2. Estimate the elastic settlement below the center of the loaded area. Assume that Df = 2 m and H = . Use Eq. (7.4).
a. Determine the largest distributed load value in lb/ft. b. Determine the point of inflection from A.