Q4). A circular curve is to be set out between two straight lines having intersectionangle (I= 12°40'), the station of the PI is 64+27.46 and the radius is 2900 ft.Calculate station PC, station PT, Long chord, external and middle ordinate for thiscurve.

Answered: 24). A circular curve is to be set out…

24). A circular curve is to be set out between two straight lines ngle (I= 12°40'), the station of the PI is 64+27.46 and the radius Calculate station PC, station PT, Long chord, external and midd

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter15: Geometric Design Of Highway Facilities

Section: Chapter Questions

Problem 7P

See similar textbooks

Related questions

Q: Consider two axially loaded columns, namely, 1 and 2, made of a linear elastic material with Young's…

A: Given data- 2 axially loaded columnsE=2×105 MPaSquare cross section areaside=10 mmlength = 1 mTo…

Q: A structure is to be built with concrete with a minimum dimension of 0.2 m, minimum space between…

A: Given:- minimum dimension=0.2mm minimum space between rebars=40mm minimum cover over rebars=40mm Two…

Q: Q4 c The use of Fibre Reinforced Polymer (FRP) in engineering materials enables engineers to obtain…

A: FIber reinforced Polymer: It is a composit material such as epoxy or vinyl ester is blended with…

Q: In the beam shown, take P1 = 4 kN, P2 = 7 kN, and W1 = 5 kN/m. a) Determine the vertical reaction…

A: Using equilibrium equation

Q: 22 Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 1.…

Q: Water flows through a 1950ft pipe 6 inches in diameter at 3 cfs. find the headloss (ft). using…

Q: A W L/2 L/2

Q: Reinforced concrete structure is a composite material consist of concrete and steel reinforcing bar,…

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B…

Q: 66. An automobile approaches a barrier at a speed of 20 m/s along a level road. The driver locks the…

Q: for the given truss a. Draw the free-body diagram without the zero-force members. b. Use the method…

A: Truss: Truss is a pin joint structure subjected to loading only on joint and there is only one force…

Q: 15m 2KN/m 15m El-Constant Analyze the beam using Moment Distribution Method Draw shear, bending…

Q: 1. From the given cross-section notes, compute the volume of earthworks between the two stations.…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 1. 26.1% of the surface area of the spherical buoy is submerged in water. Find the specific gravity…

Q: Type of Heat Treatment.

A: Heat treatment is the procedure of heating metal without allowing it to reach its molten, or…

Q: Highlight the main difference between HARN and CORS stations?

A: The user base now has access to a set of much enhanced geographical coordinates thanks to the…

Q: 5, Most structural beams are neither clamped-clamped nor simply sup- ported, but can be considered…

A: Structural Beam : A structural beam is provided to distribute the load or weight of structure safely…

Q: The discharge in a channel with bottom width 3 m is 12 m³ s¹. If Manning's n is 0.013 m-1/3 s and…

Q: From the given cross-section notes, compute the volume of earthworks between the two stations. Width…

Q: -ismattiic cc : The following readings were observed in close traverse with a ismatic compass. Where…

Q: Use the virtual work method to determine the vertical deflection and the horizontal deflection at…

Q: Why is it recommended to use a precise ephemeris when processing a static survey?

A: Precise ephemeris:- In precise ephemeris, various countries use a satellite ephemeris called the…

Q: 7-41. The double-web girder is constructed from two plywood sheets that are secured to wood members…

A: Given :

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Fluid Mechanics: Fluid Mechanics is the branch of engineering in which we study the behaviour of…

Q: oncrete, Yconc=24

A: We need to assume the max bearing pressure distribution isSame as the pressure due to water pressure…

Q: Determine the effective soil pressure if the soil bearing capacity is 130 kPa and the top of the…

A: The bearing capacity of soil is defined as the capacity of the soil which will bear the loads or we…

Q: at can resist bending moments in structures. A. Fixed B. Roller C. Hinge D. Pin E. Spring F.…

A: The roller support has only one reaction vertical or horizontal Hing and pin has two reactions…

Q: From Figure 2 below, Determine the following: 57mm 37mm 277mm 163mm | | 85mm 437mm

A: Solution: Compute the Area for the section: Area: Bottom flange: A = 37 × 277 = 10249 mm2 Web: A…

Q: How can building technology respond to the demand of the pandemic in relation to the use of building…

A: Building technology- It is the technology that is being used for the construction purposes. Building…

Q: The discharge in a channel with bottom width 3 m is 12 m³ s. If Manning's n is 0.013 m-1/3 s and the…

Q: . The following bearings of the lines observed for closed traverse BCDA. Correct the bearigs of…

Q: Please round to the nearest One Tenth (i.e., 0.1). No comma! Moist unit weight of soil, gamma = 108…

Q: Situation 4: A uniform 80-m pipe that weighs 960 kN is supported entirely by a cable AB of…

Q: bearings. : Convert the following quadrantal bearings into whole circle (a) (b) (c) (d) (e) (f) N…

Q: The grade of the concrete is M25. Find the values of design strength in- 1. Direct Compression. 2.…

A: Given data- Grade of concrete-M25To Find-design strengths

Q: he given struc

A: Take reaction at B as redundant :Deflection due to reaction =RBL33EIupDeflection due to load…

Q: Determine: RA KN, RB KN, V Diagram (2 decimal places), Vmax (kN 2 dec), Area V (2 dec), M Diagram (2…

Q: There are four forces acting on the eye bolt, three of which are indicated as shown in figure 3. The…

A: Determine the fourth force.

Q: Determine the absolute maximum shear stress developed in the beam Express your answer to three…

A: Given : Rectangular cross-section b = 3 in d = 6 in For the given loading in the beam, maximum…

Q: A 46-kN axial load P is applied to a short wooden post that is supported by a concrete footing…

A: Given P = 46 KN = 46*10³ N Required Maximum size of footing for average bearing stress of 141 KPa…

Q: The followings are the observed bearings of lines- Line F.B. AB N 74° E BC S 89° E CD S 14° W DE S…

Q: X₁ 2m .2m P₁ P₂ B 2m 2m X₂ W₁ 5m

Q: The actual velocity in the contracted section of a jet of liquid flowing from a 50mm diameter…

Q: In the beam shown, take P1 = 4 kN, P2 = 7 kN, and W1 = 5 kN/m. d) Determine the moment at X2

A: An overhang beam with a load combination of uniformly distributed load and point load is given . We…

Q: Explain what is meant by "residual stresses" in a material and how X-ray diffraction analysis can be…

A: When a load or external force is applied on a body then on response of that Internal forces are…

Q: A _is defined rectangular surface area on land based airports prepared for the landing and taking…

A: Following is required answer :

Q: D + 7 X₁ 2m M₁ 3m M2 2m X2 P₁ P₂| 2m X

Q: Q4 The water table in a certain area is at a depth of 4 m below the ground surface. To a depth of 12…

A: Given :

Q: TION ASAP!!!

A: Using equation :h=xSmSw-1x=b-ch=1.00-0.651.601-1h=0.21m

Q: Analyze the beam using Moment Distribution Method Draw shear, bending moment and elastic diagram

Concept explainers

State Plane Coordinate Systems

The state plane coordinate system (SPCS or SPS) is a collection of 124 coordinate systems or geographic zones prepared for particular regions of the U.S. Every state consists of one or more than one state plane zone, the boundaries of which generally follow the county lines. Inside the U.S., there are 110 zones in total, 10 more zones in Alaska, 5 in Hawaii, and 1 for Puerto Rico and US Virgin islands. The system is extensively used for geospatial and geographic data assembling by the state and local governments.

Question

100%

Q4). A circular curve is to be set out between two straight lines having intersection
angle (I= 12°40'), the station of the PI is 64+27.46 and the radius is 2900 ft.
Calculate station PC, station PT, Long chord, external and middle ordinate for this
curve.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bearings of backward and forward tangents are S 65°30’ E and N 75°40’ E, respectively. If the degree of curve is 8° for a full station of 20m and the stationing of the vertex is 5+005.25m, using arc basis determine the: Draw the Sketch a. Elements of the simple curve b. Station of P.C. and P.T. c. Offset from tangent distance to the 4th station and its distance along the tangent from P.C. d. Offset from the Long chord to the 5th station and its distance along the Long chord from P.C.
find the coordinates of the point in the curve y^2=12x-2y+23 that is nearest to the point P(10,4)
Provide illustration and complete solution. The azimuth from North of lines AB and BC are 330° and 25°, respectively. If a 5° simple curve is to be connected between these tangents and station of P.T. is at 28+525.69 m, find the elements of the curve.
The tangents of a simple curve have bearings of N 75° 12' Eand S 78° 36' E, respectively. What is the central angle of thecurve?
Two tangents having an azimuth of 235° and 277° meet at station 30+28.212 are connected by a 330ft spiral curvewith a 5° circular curve used for light rail transit.a) Determine the difference between the external distance of the spiral and the central curve.b) Determine the minimum super-elevation of the curve at the two-thirds of the spiral with the railway width of 15ft. If g= 32.2 ft/s^2c) Determine the stationing of the S.T.
The centerline of two parallel tracks are connected by a reversed curve. The angle of intersection of the first curve is 15 degrees and the distance between parallel tracks is 30m. If the radius of the second curve is 300m. a. Compute the length of the long chord from P.C. to P.T. ANS. 229.839m b. Compute the radius of the first curve. ANS. 580.432m please also include the drawing of the curve
From a known point V (vertex), the tangent lines of a compound curve are drawn -having azimuths 300° (forward tangent) and bearing N 04° E (back tangent),respectively. A common tangent line CD intersects the two tangent lines at bearing S 34° E. Stationing of the vertex of the compound curve is 16 + 464.35 and the distance from point D to the vertex of the compound curve is 137.6 m. If the external distance of the curve passing through the PC is 1.42 times the external distance of the simple curve that passes through the PT, solve for the following.a. Radius of the curve that passes through the PCb. Radius of the curve that passes through the PTc. Stationing of the PTWrite the given and required. List the graph/table. Box the final answer.
The perpendicular offset of the PT of a simple curve is 120.20m. If the angle ofintersection is 50֯, determine the length of the long chord. Note: Draw the given data.
The bearings of backward and forward tangents are S 65°30’ E and N 75°40’ E, respectively. If the degree of curve is 8° for a full station of 20m and the stationing of the vertex is 5+005.25m, using arc basis determine the: provide sketch as well a. Elements of the simple curveb. Station of P.C. and P.T.c. Offset from tangent distance to the 4th station and its distance along the tangent from P.C.d. Offset from the Long chord to the 5th station and its distance along the Long chord from P.C.
Provide complete solution and illustration. The bearings of backward and forward tangents are S 65°30’ E and N 75°40’ E, respectively. If the degree of curve is 8° for a full station of 20m and the stationing of the vertex is 5+005.25m, using arc basis determine the: a. Elements of the simple curveb. Station of P.C. and P.T.c. Offset from tangent distance to the 4th station and its distance along the tangent from P.C.d. Offset from the Long chord to the 5th station and its distance along the Long chord from P.C.
A 4.5-degree circular curve is to connect two tangent lines with a 55.5-degree external angle. The PI station is 25+30.25. Determine R, LC, T, E, PC station, and PT station.
A 5 degree circular turnout is to connect a railway track, leading due east, to the mouth of the tunnel which is 70m. from the station 7+812. Use Chord Basis. Determine the radius of the curve in meters. Ans. 229.30