edu/courses/1224156/assignments/11908891?module_item_id%3D23919723cion Pr...M3 Prenatal Develo...S SOAP2DAYVideos | BabyCenterNew Tab29 ft12 ftFind the perimeter & area of the figure pictured above. (The figure is not drawn to scale and remember touse T2 3.14 for all calculations involving 7).Perimeter =ftRound answers to 2 decimal places as needed.Perimeter =ydRound answers to 2 decimal places as needed.Area =ft2Round answers to 2 decimal places as needed.Area =in2Round answers to 2 decimal places as needed.Submit Question

Answered: Image /qna-images/answer/51839713-8e03-4d31-b4fe-6f9433ecec3c.jpg

29 ft 12 ft Find the perimeter & area of the figure pictured above. (The figure is not drawn to scale and remember to use T 3.14 for all calculations involving 7). Perimeter ft %3D Round answers to 2 decimal places as needed. Perimeter yd %3D Round answers to 2 decimal places as needed. Area = ft2 Round answers to 2 decimal places as needed. Area = in2 Round answers to 2 decimal places as needed.

29 ft 12 ft Find the perimeter & area of the figure pictured above. (The figure is not drawn to scale and remember to use T 3.14 for all calculations involving 7). Perimeter ft %3D Round answers to 2 decimal places as needed. Perimeter yd %3D Round answers to 2 decimal places as needed. Area = ft2 Round answers to 2 decimal places as needed. Area = in2 Round answers to 2 decimal places as needed.

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter16: Table Of Decimal Equivalents And Combined Operations Of Decimal Fractions

Section: Chapter Questions

Problem 36A: A slot is machined in a circular plate with a 41.36-millimeter diameter. Two milling cuts, one 6.30...

See similar textbooks

Similar questions

A slot is machined in a circular plate with a 41.36-millimeter diameter. Two milling cuts, one 6.30 millimeters deep and the other 3.15 millimeters, are made. A grinding operation then removes 0.40 millimeter. What is the distance from the center of the plate to the bottom of the slot? All dimensions are in millimeters.
Find inside caliper dimension x. All dimensions are in inches.
SOLID MENSURATION III
The measurement of a side of a square is found to be 10 cm, with a possible error of 0.05 cm. A. Approximate the percent error in computing the area of the square. ______ B. Estimate the maximum allowable percent error in measuring the size of the error in computing the area cannot exceed 2.9% ______
The Deepwater Horizon oil spill in the Gulf of Mexico on April 20, 2010 was "an environmental disaster of unprecedented proportions" and was a "devastating blow to the resource-dependent economy of the region" [1]. According to the Washington Post, it is estimated that 9857 9857 cubic meters of oil per day spilled into the Gulf of Mexico on August 2, 2010 Assume that an average of 9857 m^3/day of oil spilled into the Gulf of Mexico everyday and that it formed a hemispherical dome of radius r on the ocean floor. D) find the rate of change of the radius with respect to time when the volume of the oil spill is 50,000m^3. E) Since only the oil that is in contact with seawater can mix with seawater, it is important to know how much of the surface area of the oil spill is in contact with seawater. Find the rate of change of the hemisphere's surface area with respect to time when the volume of the oil spill is 50,000 m3. Include units in your answer. You should assume that only the top…
The Deepwater Horizon oil spill in the Gulf of Mexico on April 20, 2010 was "an environmental disaster of unprecedented proportions" and was a "devastating blow to the resource-dependent economy of the region" [1]. According to the Washington Post, it is estimated that 9857 9857 cubic meters of oil per day spilled into the Gulf of Mexico on August 2, 2010 Assume that an average of 9857 m^3/day of oil spilled into the Gulf of Mexico everyday and that it formed a hemispherical dome of radius r on the ocean floor. A) find a formula for the volume of oil spilled in cubic meters, t days after the start of the oil spill. Include units in answer B) find the derivative of volume formula with respect to time. Include units in answer. C) when the volume of the oil spill is 50,000m^3, what is the radius of the hemisphere of oil? Include units in your answer. Give your answer accurate to 3 decimal places. D) find the rate of change of the radius with respect to time when the volume of…
Subject: Solid Mensuration
PT. X is an industry engaged in concrete steel with various diameter sizes. The product that is mostly produced is concrete iron with a diameter of 12 mm because it suits the needs of consumers and the current pandemic conditions. During the period from January to December 2019, PT. X is capable of producing as many as 6800 tonnes of units. From the results produced, there is a product defect of 70.4 with the type of product damage, namely overfill (wing), overlap (excessive shape), underfill (kempong) and scratch (beret). In that period, defects were found above the tolerance limit of 2%, namely at week 5 and week 12 of 2.42% and 2.21%. During the production process PT.X has a 2% probability of producing defective products. If you check is 065, then determine:a. P(X=0)b. P(X=1)c. P(X=2)d. P(X≤2)e. P(X≥3)
defermine the appvoximate volume of cyliuder height 1,002 cm and diametev of 2,002 cm , using diffvential Concept
Assembled workstations are subjected to a final inspection for the surface defects. In the last 25 observations the allowable number of defects is 7. What is the Action Limit?
Compare the vaules using the symbols < > =
SOLID MENSURATION II