29knd. A cylinder of 50 mm diameter and height 60 mm is resting on base in H.P. A circular hole of 20 mm diameter is drilled , so that the axis of the hole is perpendicular to V.P and bisects the axis of cylinder at right angles . Draw the development of the lateral surface of the cylinder with the slot . Draw neatly with pencil and take correct values must**

29knd. A cylinder of 50 mm diameter and height 60 mm is resting on base in H.P. A circular hole of 20 mm diameter is drilled , so that the axis of the hole is perpendicular to V.P and bisects the axis of cylinder at right angles . Draw the development of the lateral surface of the cylinder with the slot . Draw neatly with pencil and take correct values must**

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.86RP: The flanged bolt coupling is fabricated by drilling 10 evenly spaced 0.5-in. diameter bolt holes in...

See similar textbooks

3

Draw neatly with pencil and take correct values must**

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The properties of the unequal angle section are Ix=80.9in.4,Iy=38.8in.4, and Iu=21.3in.4. Determine Ixy.
Using the method of composite areas, find the dimension h that maximizes the centroid coordinate y of the plane region shown.
The flanged bolt coupling is fabricated by drilling 10 evenly spaced 0.5-in. diameter bolt holes in a steel plate. The radii of the plate and bolt circle are 5 in. and 4 in., respectively. Determine the percent reduction in the polar moment of the area about point O due to the drilling operation.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Use integration to verify the formula given in Table 9.2 for Ixy of a half parabolic complement.
Use integration to find Ix,Iy, and Ixy for the shaded region shown.
A centroid is an object's geometric center. For an object of uniform composition, its centroid is also its center of mass. Often the centroid of a complex composite body is found by, first, cutting the body into regular shaped segments, and then by calculating the weighted average of the segments' centroids.An object is made from a uniform piece of sheet metal. The object has dimensions of a = 1.05 ft , where a is the diameter of the semi-circle,b = 3.74 ft , and c = 2.45 ft . A hole with diameter d = 0.700 ft is centered at (0.925,0.525) . Part A Find the area of the body. (Figure 1) Express your answer numerically in feet squared to three significant figures. Part B Find x¯ , the x -coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures. Part C Find y¯ , the y -coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures.
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Suppose that a= 640 mm
A block of stone is cut so that its cross‑section is a parallelogram. The width of the bottom side is ?=0.655 m, the height of the top of the block is ℎ=0.915 m, and the top right corner overhangs a distance ?oh=0.195 m from the bottom corner as shown. Assume that the block is of uniform density, so that the center of gravity of the block is located at the geometric center.
Please evaluate the shape factor and answer d)
A hexagonal plane of side 30mm has a corner on the ground. Its surface is inclined at 45 degree to the HP and perpendicular to the VP . Draw its projections when the diagonal through the corner in the HP is parallel to the VP.
4 A frustum of a cone 72 mm diameter of circular base, 48 mm diameter of top and having anaxis of 72 mm length has a hole of 30 mm diameter drilled centrally through its flat faces.The frustum rests on the rim of its base in such a way that the base makes an angle of 45° toHP and the axis is in a vertical plane parallel to VP. Draw its elevation and plan