2)A pipe filled with water has a gauge attached to it. The gauge reads a pressure of 4.00 atm. a) How large is the absolute pressure inside this pipe? b) A small hole is made in the pipe. At what speed does the water emerge through the hole?

2)A pipe filled with water has a gauge attached to it. The gauge reads a pressure of 4.00 atm. a) How large is the absolute pressure inside this pipe? b) A small hole is made in the pipe. At what speed does the water emerge through the hole?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM # 3 1. A solid block is 70 cm wide, 80 cm long and 20 cm tall, and has a mass of 6700 gm. Estimate the solid block volume (in m). 2. Estimate the density of the block in kg/ m. 3. If the block were floating in fresh water (with the 70 cm by 80 cm face down), the block would be submerged under water by what length? 4. How much extra mass can the block support without sinking?
A freshly cut log floats with one fourth of its volume protruding above the water surface. The specific weight of the log is... ...pounds per cubic feet. Assume the specific weight of the water is 62.4 pounds per cubic feet. Please note: You have all the data you need to solve this problem. Begin by drawing a schematic. Then draw a Free Body Diagram of the forces.
A rectangular plate 1.1m x 1.75m is submerged in water and makes an angle of 30° with the horizontal, the 1.1m sides being horizontal. Calculate the magnitude of the force on the plate and the location of the point of application of the force, with reference to the top edge of the plate, when the top edge of the plate is: a) At the water surface. b) 500mm below the water surface
An inverted test tube partially filled with air floats in a plastic Question 1 water-filled soft drink battle as shown in the figure. The amount of air in the tube has been adjusted so that it just floats. The bottle cap is securely fastened. A slight squeezing of the plastic bottle will cause the test tube to sink to the bottom of the bottle. Explain why does the tube float by drawing a free body diagram that a) clearly illustrates all forces applied on it? b) c) test tube if the water was replaced with a higher density fluid? Why does the tube sinks after squeezing the plastic bottle? What is the change in the magnitude of the squeeze needed to sink the Air Test tube Water -Plastic bottle
1.When a double-bottom tank is full of fresh water it holds 120 tonnes.Find how many tonnes of ol of relative density 0.84 it will hold. 2. A tank measures 20 m. X 24m X 10.5 m. and contains oil of relative density 0.84.Find the mass of oll it contains when the ullage is 2.bm. (Ulage is the distance from the surface of the liquid in the tank to the top of the tank)
A pontoon boat floats on two cylindrical pontoons (assume the ends are flat). Each pontoon is 6m long. The mass of the boat, pontoons, and gear (without any passengers) is 1950 kg. If exactly half of the pontoon volume was submerged without any passengers on the boat, what is the maximum volume of water that can be displaced to support the weight of passengers? The density of freshwater is 1000 kg/m³ . End view of pontoons: Waterline Pontoon D/2 is submerged
State Pascal’s principle and give one application of the principle. An object is dropped into a beaker of water. Two forces are operating on the object viz. the weight of object and the buoyant force FB due to the fluid. Explain, in terms of the forces when the object. a.) Sinks to the bottom of the beaker b.)Floats in the water A hydraulic press for compacting powdered samples has a large cylinder with a diameter of 10.0 cm and a small cylinder of diameter 2.0 cm. If a force of 350 N is applied to the small cylinder, what will be the force exerted by the fluid on the large cylinder? Be consistent with your units.
A loaded scow has draft of 1.6 m in sea water (sg = 1.03) when in upright position. The scow is 6 m wide and 12 m long and 2.4 m high. The center of gravity of the scow is 1.8 m above the bottom along the vertical axis of symmetry. Assume that the center of buoyancy is located half of the height of draft. What is the maximum single weight in kN that can be moved transversely from the center of the unloaded scow over the top edge without sinking the scow? (Considering rolling position)
A 130 cc block has a piece of lead tied to it. Suppose that the SG of lead is 11.13 and SG of the block is 0.25 and it floats just submerged in the water, What is the weight of the lead? (Answer must be in grams) Water Surface Block Lead
A container lying horizontally is filled with water. It is 5 ft long and its cross section is in the shape of a semicircle with diameter 3 ft at the top. The weight density of water is 62. 4 lb/ft. (Draw an illustration.) a. How much work is required to pump all the water to the top of the tank? b. Find the force due to fluid pressure on one semicircular end of the container.
13) A trapezoidal plate 4 feet wide at the bottom, 7 feet wide at the top and 3 feet high is submerged with the top side parallel to the surface and 10 ft below the water. Find the force against the plate. (assume pg=62.4 lb/ft³)
A barge pulled by a tugboat can be described as a rect- angular box that is open on the top. A certain barge is 30.2 feet wide and 12.50 feet high, with the base of each side being 116 feet long. If the barge itself weighs 6.58 x 10 pounds, what will be the draft (depth in the water) if the cargo weighs 1.12 × 10°pounds in (a) sea- water with a density of 1.025 g/mL and (b) freshwater with a density of 0.997 g/mL?