please explain in neat hand writing so I can undertstand 3) A 0.5 inch diameter aluminum rod is used to support a decorative overhang. If the 7ft rod deforms0.024inches under loading, what is the load on the rod caused by the overhang? Use E = 10,000 ksi.4) A 15ft W12x40 steel column is supported by a steel base plate, concrete pedestal and concrete footingas shown below. If a W12x40 section has a cross-sectional area of 11.7 in^2, what axial deformationwould occur in the column under the load shown.60 kipsColumn – W12 x 40Square base plate – 14" X 14"24-in.-diameter pedestalSquare footing - 4' - 0" x 4'-0"5) If the circular concrete pedestal is 6inches thick, what is the transverse deformation in the pedestal?Use Econc = 3,500,000 psi and Poisson's Ratio is 0.15.

NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost…

Answered: 3) A 0.5 inch diameter aluminum rod is…

3) A 0.5 inch diameter aluminum rod is used to support a decorative overhang. If the 7ft rod deforms 0.024inches under loading, what is the load on the rod caused by the overhang? Use E = 10,000 ksi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.6P: A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure)....

See similar textbooks

Related questions

Q: ir in a vessel having a volume of 5m3 at 3.0bar is compressed to 3m3 without any change of temperatu...

A: Given Data : Initial volumeV1=5 m3 Initial pressureP1=3 bar Final volumeV2=3 m3

Q: Steam enters an adiabatic turbine operating at steady state with an enthalpy of 3251.0kJ/kg and leav...

Q: Question: Calculate the kinetic energy in joules of a 150 lb jogger (68.1 kg) traveling at 12.0 mile...

A: Given data : Mass of a jogger=m Velocity of jogger=V To find : Kinetic energy

Q: inverse kinematics of

A: introduction: we have to find out inverse kinematic

Q: A 5-feet diameter Chimney is designed to handle a flue gas produced in a steam power plant at a rate...

A: The goal of a chimney is to exhaust combustion products (smoke and gases) from the appliance onto th...

Q: - General Form of Designation. A. Carbon Content in Points or hundredths of percent B. Major Alloyin...

Q: thermodynamic2

A: Given Data : Thermodynamics

Q: Water under a gauge pressure of 350 kPa flows with a velocity of 5m/s through a right- angle bend th...

A: As per given question Inlet pressure =350kpa Inlet velocity =5m/s Right angle bend=250mm We have to...

Q: Express the boundary conditions on each boundary for each problem shown below. y

A: To find Boundary conditions

Q: Problem Solving - Solve what is required. For accuracy, retain at least 4 decimal points in solving....

A: Note: As question includes three unrelated parts, Answer of first part is provided as per the policy...

Q: A B E F 20 kN-m 35 kN-m 85 kN-m 30 kN-n

A: given d=0.2m = 200mm so r = 100mm

Q: A cantilever beam is supported at B by cableBC. The beam carries a uniform load q = 200 N/m.If the l...

A: Let us suppose that there is no cable at the end B of the beam, thus the deflection of point B in th...

Q: Heat transfer Question Please explain how to write an excel spreadsheet that will calculate the temp...

Q: A simply supported beam is loaded as shown in the Figure. The corresponding SFD and BMD would be: 20...

Q: When can the conductive thermal resistance of the tube in a heat exchanger be neglected in overall h...

Q: Select the beam loading that corresponds to this moment diagram. M

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2 ...

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. F,| = 4 kN %D 1....

Q: The two cars collide at right angles in the intersection of two icy roads. Car A has a mass of 1985 ...

Q: 1. An Otto cycle has an initial condition of 100 kPa and 30°C. The compression ratio is 10 and the m...

A: i have answered as per your request

Q: 01: The coplanar force system shown in Figure below is subjected to a couple moment, three concentra...

A: Take sum of forces in X axis =∑FX =90+ 45+ 50 sin(36.86)-25 cos(60) - 40 sin(45) = 124.208 N Take su...

Q: Calculate the acceleration of block A, in

Q: Objects that are falling toward Earth move * O at a constant velocity slower and slower. faster and ...

A: Objects that are falling toward earth move faster and faster. By equation of kinematics, v= u + at, ...

Q: Two boxes A and B, each having a weight of 160 Ib, sit on the 500-lb conveyor which is free to roll ...

Q: 17/ The fertilizer spreader and the fertilizer it contains have a combined mass of 40 kg and a cente...

A: Givenm=140kgC=5mm

Q: A steam engine cylinder has an effective diameter of 35 cm and the maximum steam pressure acting on ...

Q: For a long slender column has uniform cross section, the ratio of critical buckling load for the cas...

A: Given data, There are two different case, 1st case- both end clamped (fixed) to the case 2nd case...

Q: 3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an e...

Q: State one mechanical material property and one non-mechanical material property that would be import...

A: Given Treadle design To find 1. Mechanical properties 2. Non mechanical properties 3. Material suita...

Q: in compression, determine the factor of safety against failure:

Q: A particle moves along the x-axis with velocity given by v(t) = 3t 2 + 6t for time t> 0. If the part...

A: Given data: vt=3t2+6t Need to determine the position of the particle at t=1 sec.

Q: k m=1.5 kg x(t) 2X Derive the equation of motion for the system in absolute coordinate(x)

Q: Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate o...

A: Given Data Weight W = 70 Kg Spring rate for spring 1= 0.209 Kg/mm Spring rate for spring 2 and 3=...

Q: to the right, determine the velocity of cylinder B. The velocity of Bis positive if downwa

A: need to find velocity of cylinder B

Q: A skier starts from rest on the 45° slope at time t = 0 and is clocked at t = 2.64 s as he passes a ...

Q: G3 R(s) Cs) G2 H2

Q: determine the size of the punch,

A: Given data; For a circular blanking operation;Size of the blank=30 mmThickness of the sheet, t= 3 mm...

Q: The total length of a first class lever is 9.0 ft. This is used to move a load of 390 lbs, as pictur...

Q: The cross-sectional dimensions of a beam are shown. Assume b=3.625 in., t=tw=0.1875 in. and d=4.125 ...

Q: cular solid disc of uniform thickness 25 mm, us 225 mm and mass 25 kg, is used as flywhee rotates at...

Q: Using the coordinate system shown, the number of reactions about point O equals

Q: A circular shaft is subjected to combined loads of bending M and torque T. With the help of Mohr's c...

A: Circular shaft is subjected to combined loads of bending M and torque TNow,Bending stress induced in...

Q: In a transaxle, the pinion gear on the pinionshaft meshes with the ___.a. reverse idler gearb. ring ...

A: Given Data : Transaxle

Q: Advanced hybrid materials technology has been used in automotive applications. A good example is eng...

A: Hybrid composite materials are employed in a variety of engineering applications due to their div...

Q: Draw the diagram of float sensor and bellows and capsules explain its operation in detai

Q: The centroid distance y and the second moment of area INA of the channel section are 40 mm and 6 x 1...

A: GivenINA=6×10-6m4M=10kNmy=40mm =0.040m

Q: open cycle gas turbine employs a regenerative arrangement. The air enters the compressor at 1 bar an...

Q: QUESTION 5 Knowing that the tension in cable AC is 1065 N, determine the moment about each of the co...

Q: the furnace to build the chimney top are provided in Section B-B 16. Regarding wood framing, A. head...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: Which invariant reaction can be recognized in 2300 210 1900 1700 1500 1300 Temperature, "C (A)

A: the peritectic reaction can be easily recognized in the phase diagram.

Concept explainers

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.

Question

please explain in neat hand writing so I can undertstand

3) A 0.5 inch diameter aluminum rod is used to support a decorative overhang. If the 7ft rod deforms
0.024inches under loading, what is the load on the rod caused by the overhang? Use E = 10,000 ksi.
4) A 15ft W12x40 steel column is supported by a steel base plate, concrete pedestal and concrete footing
as shown below. If a W12x40 section has a cross-sectional area of 11.7 in^2, what axial deformation
would occur in the column under the load shown.
60 kips
Column – W12 x 40
Square base plate – 14" X 14"
24-in.-diameter pedestal
Square footing - 4' - 0" x 4'-0"
5) If the circular concrete pedestal is 6inches thick, what is the transverse deformation in the pedestal?
Use Econc = 3,500,000 psi and Poisson's Ratio is 0.15.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

.16 Three identical, solid circular rods, each of radius r and length L, are placed together to form a compression member (see the cross section shown in the figure). Assuming pinned-end conditions, determine the critical load Pcr The rods act independently as individual columns. The rods are bonded by epoxy throughout their lengths so that they function as a single member. What is the effect on the critical load when the rods act as a single member?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and inside diameters of 3.5 in. and 2.9 in., respectively. What is the maximum permissible length Lmaxof the column if E = 29,000 ksi and y = 36 ksi?
A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 6 ft, 9 ft, 12 ft, and 15 ft. The column has an outside diameter d = 6.625 in. and wall thickness t = 0.280 in, (Assume E = 29,000 ksi and y= 36 ksi.)
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 900 kN. Using a factor or safely 3.0 with respect to ultimate strength, determine the outer diameter of the pier if the thickness, is of the cross section is 12 mm.
The figure shows an idealized structure consisting of two rigid bars joined by an elastic connection with rotational stiffness ßR. Determine the critical load PCTfor the structure.
Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 2,6 m, 2.8 m, 3.0 m, and 3.2 m. The column has an outside diameter d = 140 mm and wall thickness t = 7 mm, (Assumed = 200 GPa and ( y= 250 MPa.)
Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 500 kN (see figure). The column has an outside diameter d = 200 mm, wall thickness; = 10 mm, E = 200 GPa, and y = 250 MPa.