A light fixture of negligible mass, has three applied forces acting on it as shown.|F,| = 4 kN1.2 m1.2 m1.2 m2.8 m|F,| = 6 kN-y 45°|F| = 5 kN%3DUsing the coordinate system shown, the number of reactions about point 0 equalsAnswer:

Answered: Image /qna-images/answer/0dfe6f84-246b-497d-9865-a5cdf7b28965.jpg

Answered: Using the coordinate system shown, the…

Engineering

Mechanical Engineering

Using the coordinate system shown, the number of reactions about point O equals

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Five masses m1, m2, m3 m4 and m5 are 150 kg, 250 kg, 190 kg , 120 kg and 210 kg respectively. The corresponding radii of rotation are 0.2 m, 0.15 m, 0.25 m 0.1 and 0.3 m respectively and the angles between successive masses are 45°, 75° 20 and 110°. Find the position and magnitude of the balance mass required, graphically, if its radius of rotation is 0.25 m
Four masses m1, m2, m3 and m4 are 100 kg, 200 kg, 140 kg and 160 kg respectively. The corresponding radii of rotation are 0.2 m, 0.15 m, 0.25 m and 0.3 m respectively and the angles between successive masses are 30°, 75° and 100°. Find the position and magnitude of the balance mass required, graphically, if its radius of rotation is 0.2 m.
The forearm shown below is positioned at an angle θ with respect to the upper arm, and a 5.0-kg mass is held in the hand. The total mass of the forearm and hand is 3.0 kg, and their center of mass is 15.0 cm from the elbow. (a) What is the magnitude of the force that the biceps muscle exerts on the forearm for θ = 60°? (b) What is the magnitude of the force on the elbow joint for the same angle? (c) How do these forces depend on the angle θ ?
In principle of Moments experiment, test 1(equal distanced forces) is applicable to ____ a. Non - coplanar concurrent force system. b. coplanar concurrent force system c. coplanar collinear force system d. coplanar parallel force system
Topic: Couples, Resultant of Force Systems & Equilibrium If F1 = 10N, F2 = 15N, F3 = 8N, F4 = 10N, F5 = 18N, and the length of te side of a red square is 1m. Calculate magnltude (+ for CCW, - for CW) of the resuItant moment (N-m) about point A. Calculate the magnitude of the reItant f0rce (N). (Answer: 50.80Nm, 20.33N)
550 g static mass Time to Complete 60 Revolutions 39 sec Radius of Rotation for the Rotating Mass . 144 m Mass of the Rotating Mass . 449 kg % Difference Between the Static ans Centripetal Forces
Find the magnitude of the force exerted on bolt A, given:P = 100 lb, L1 = 1.4 in, L2 = 5.4 in, L3 = 12 in, L4 = 0.4 in, L5 = 1 in
Plunger (weightless) Area is 0.003 m² piston mass 1000 kg , area of piston is 0.3 m² density of oil is 750 kg/m³ determine force on Plunger required for equilibrium
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is given as γ=8°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=50°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N)b) Find the tensile force T2 in cable 2. (Write your result in N)c) Find the angle α of cable 1 with the horizontal.
1) Diagram below shows four masses M,E,R,S carried by a rotating shaft at radii 100, 125, 200 and 150 mm respectively. The mass of E,R,S are 10 kg, 5 kg, and 4 kg respectively. The planes in which the masses revolve between M and E are 2mm, E and R are 1mm, R and S are 1mm. Determine the required mass of A, mA and the angles a,b,c relative to mass B so that the shaft shall be in complete balance.
3-In the scheme below, 4 objects are hanging from each of the rings and 5 ropes (blue) keep the entire scheme in balance. The known values are m1=30 kgm1=30 kgα=60ºα=60ºβ=30ºβ=30ºγ=70º a) Attach the force diagram on each of the rings with the graphical decomposition of the forces that are not exclusively on the Cartesian axes. b) Determine the tractions T1, T2, T3, T4 and T5. c) Determine the mass of weights 2, 3, 4 and 5. Tip: If you feel comfortable, use software to solve the systems of equations.
I need your help expert. The system shown below is in equilibrium. Spring 3 is known to have a change in length of 10 cm. The magnitude of the compressive force in Spring 2 is 15% more than the magnitude of force P, while the magnitude of the compressive force in Bar 1 is 100 N less than that in Spring 2. If the spring constants of Springs 2 and 3 are 625 and 1200 N/m, respectively, determine the following: a. magnitude of forces P (in N) and F (in N) b. tension (in N) in cable ABC c. mass (in kg) of Block A d. compressive force in Bar 1 e. change in length (in cm) of Spring 2 Draw the complete FBD’s of Block A, Hook C and Pulley E. (Note: Below are the final answers, kindly match your answer on this. Thank you) Answer: P = 131.2831 N, F = 87.1569 N, TABC = 110.7024 N, mA = 15.6338 kg, F1 = 50.9756 N, s2 = 24.1561 cm