(3) A thick steel slab is initially at a uniform temperature of 25°C. When the slab is exposed to hot flue gases, the surface temperature suddenly changes to 450°C. Make calculations for the temperature in a plane 250 mm from the slab surface 5 hours after the operation of change in surface temperature. Find also the heat flowing into 2 square meters of this plane and the total energy flowing through the surface during the 5 hour period. It may be presumed that for steel, thermal conductivity k = 160 kJ/m hr deg, density p = 8000 kg/m³ and the specific heat capacity Cp = 0.48 kJ/kg deg.

(3) A thick steel slab is initially at a uniform temperature of 25°C. When the slab is exposed to hot flue gases, the surface temperature suddenly changes to 450°C. Make calculations for the temperature in a plane 250 mm from the slab surface 5 hours after the operation of change in surface temperature. Find also the heat flowing into 2 square meters of this plane and the total energy flowing through the surface during the 5 hour period. It may be presumed that for steel, thermal conductivity k = 160 kJ/m hr deg, density p = 8000 kg/m³ and the specific heat capacity Cp = 0.48 kJ/kg deg.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.40P

See similar textbooks

Similar questions

1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
Shown below is an insulated copper block that receives energy at a rate of 100 W from anembedded resistor. If the block has a volume of 10-3 m3and an initial temperature of 20oC, howlong would it take, in minutes, for the temperature to reach 60oC? Copper has a specific heatcapacity ccu = 0:385 kJ/ kg.K and a density of cu = 8930 kg/m3.
2. A large sheet of glass 2” thick is initially at 300oF throughout. It is plunged into a stream of running water having a temperature of 60oF. How long will it take to cool the glass to an average temperature of 100oF. For glass k = 0.40BTU/ft-hroF, ρ = 155 lb/ft3 and Cp = 0.20 BTU/lboF.
A cylindrical body having 10 cm diameter and lenth of 30 cm passes through a heat treatment furnace which is 6 m in length. The body must reach a temperature of 800°C before it comes out of the furnace. The furnace gas is at 1250°C and body initial temperature is 90°C. How much time it will take to attain the required temperature ? Take h = 100 W/m² °C. Take K(steel) = 40 W/m°C and a (thermal diffusivity of steel) = 1.16 x 10-5 m²/s.
A mother takes the milk to be given to her baby from the refrigerator and pours it into a cylindrical bottle for heating. The height of the milk in the bottle is 10 cm. Then he places the bottle into a large container with hot water at a temperature of 62 ° C. The heat transfer coefficient between hot water and bottle is 130 W / m2.oC. The process of heating the milk from 4 0C to 40 0C is required to be completed within 6 minutes. What should be the diameter of the bottle used? The properties of milk can be equal to the properties of water at the same temperature.