3500J / s of energy is transferred from a heat source to the surface of the part. The heated region is circular and the heat density decreases as the radius increases. Find out whether the heat density is sufficient to melt the metal since 70% of the heat is concentrated in a circle with a diameter of 3.75 mm.

3500J / s of energy is transferred from a heat source to the surface of the part. The heated region is circular and the heat density decreases as the radius increases. Find out whether the heat density is sufficient to melt the metal since 70% of the heat is concentrated in a circle with a diameter of 3.75 mm.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.34P: 2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material...

See similar textbooks

Similar questions

a. What is the heat flux, q"1 [in W/m2], at the left-hand side of layer B? Express your answer as a negative number if the heat flux goes to the left, and as a positive number if the heat flux goes to the right. b.What is the heat flux, q"2 ( in W/m2) at the right-hand side of layer B? Express your answer as a negative number if the heat flux goes to the left, and as a positive number if the heat flux goes to the right. c. What is the temperature, T1, on the left-hand side of layer B, in Celsius? d. What is the temperature, T2, on the right-hand side of layer B, in Celsius?
During a picnic on a hot summer day, the only available drinks were those at the ambient temperature of 90°F. In an effort to cool a 12-fluid-oz drink in a can, which is 5 in high and has a diameter of 2.5 in, a person grabs the can and starts shaking it in the iced water of the chest at 32°F. The temperature of the drink can be assumed to be uniform at all times, and the heat transfer coefficient between the iced water and the aluminum can is 30 Btu/h·ft2·°F. Using the properties of water for the drink, estimate how long it will take for the canned drink to cool to 40°F.
If H is the work output of a heat engine and Q is the total heat input of an engine, then determine its thermal efficiency.
The 8-mm-thick bottom of a 220-mm-diameter pan may be made from aluminum (k = 240 W/m · K) or copper (k = 390 W/m · K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C. If heat is transferred from the stove to the pan at a rate of 600 W, what is the temperature of the surface in contact with the stove for each of the two materials?
What is the approximate temperature difference between a hot plate and the surrounding air if the heat flux from the plate is 800 W/m2? Assume that the air is flowing past the surface with a velocity of 5 m/s giving a heat transfer coefficient of 20 W/(m2K).
The cylinders that come out of the heat treatment furnace are cooled in a stagnant air environment in a horizontal position. The cylinders have a diameter of 100 mm and a length of 0.1 m. The temperature of the cylinders is 440 ° C and the ambient temperature is 20 ° C. Calculate the heat transfer from 10 cylinders to the environment. a) 3125 W b) 2350 W C) 1848 W d) 1354 W e) 2750 W
An electric generator at a power plant produces energy by passing superheated steam from a high temperature container (reservoir), through a pipe connected to a series of fans, and then into a low temperature reservoir. As the steam passes across the blades of the fans some of the heat energy of the steam is transformed into mechanical energy, which turns the fans which in turn are connected to a generator, which in turn converts the mechanical energy into electrical energy. If the high temperature steam has a temperature of 201.9 K and the low temperature reservoir has a temperature of 154.1 K, what is the Carnot efficiency of this process?
Q#01: Write a short note on the following: What are the best possible solutions to increase the heat transfer rate of a body? Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer.
A mother takes the milk to be given to her baby from the refrigerator and pours it into a cylindrical bottle for heating. The height of the milk in the bottle is 10 cm. Then he places the bottle into a large container with hot water at a temperature of 62 ° C. The heat transfer coefficient between hot water and bottle is 130 W / m2.oC. The process of heating the milk from 4 0C to 40 0C is required to be completed within 6 minutes. What should be the diameter of the bottle used? The properties of milk can be equal to the properties of water at the same temperature.
n electric generator at a power plant produces energy by passing superheated steam from a high temperature container (reservoir), through a pipe connected to a series of fans, and then into a low temperature reservoir. As the steam passes across the blades of the fans some of the heat energy of the steam is transformed into mechanical energy, which turns the fans which in turn are connected to a generator, which in turn converts the mechanical energy into electrical energy. If the high temperature steam has a temperature of 412.1 K and the low temperature reservoir has a temperature of 105.4 K, what is the Carnot efficiency of this process?
It is common knowledge that the temperature of air rises as it is compressed. An inventor thought about using this high-temperature air to heat buildings. He used a compressor driven by an electric motor. The inventor claims that the compressed hot-air system is 25 percent more efficient than a resistance heating system that provides an equivalent amount of heating. Is this claim valid, or is this just another perpetualmotion machine? Explain.
The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is increased by a gearbox that has an efficiency of 0.93. In turn, the gearbox output shaft drives an electric generator with an efficiency of 0.95. The cylindrical nacelle, which houses the gearbox, generator, and associated equipment, is of length L = 6 m and diameter D = 3 m. If the turbine produces P = 2.5 MW of electrical power, and the air and surroundings temperatures are T = 25 oC and Tsur = 20 oC, respectively, determine the minimum possible operating temperature inside the nacelle. The emissivity of the nacelle is 0.83, and the convective heat transfer coefficient is h = 35 W/m2 .K. The surface of the nacelle that is adjacent to the blade hub can be considered to be adiabatic, and solar irradiation may be neglected. Use Fin or N number of fins to reduce the Ts of the nacelle less than 143 oC