3) A torque is to be carried by a flanged bolt coupling that consists of ten 16 mm- diameter steel bolts on a circle of diameter 400mm and eight 12mm-diameter steel bolts on a circle of diameter 250mm. a) Determine the torque if the shearing stress in the 12mm diameter bolts is 20MPA. b) How many 16mm diameter bolts should be added to increase the torque to 12 kN-m?

3) A torque is to be carried by a flanged bolt coupling that consists of ten 16 mm- diameter steel bolts on a circle of diameter 400mm and eight 12mm-diameter steel bolts on a circle of diameter 250mm. a) Determine the torque if the shearing stress in the 12mm diameter bolts is 20MPA. b) How many 16mm diameter bolts should be added to increase the torque to 12 kN-m?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 56 MPa, how many 18 mm-diameter steel bolts must be used on a 300 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft?
A flanged bolt coupling consists of 9-17-mm-diameter steel bolts on a bolt circle 600 mm in diameter, and 5-17-mm-diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 66 MPa in the bolts? Answer must be in kN-m.
3.Determine the torque that can be applied on a flanged bolt coupling consisting of eight 10- mm diameter steel bolts on a bolt circle 400 m in diameter, and a six 10-mm diameter steel bolts on a concentric bolt circle of 300 mm diameter, without exceeding a shearing stress of 60 MPa in the bolts.
PLEASE ANSWER ASAP TY! a) What is the magnitude of internal torque in segment CD (in N-m)? b) What is the magnitude of internal torque in segment AC (in N-m)? c) What is the magnitude of torsional shear stress in segment DB (in MPa)? d) Determine the maximum torsional shear stress in the shaft (in MPa). e) What is the angle of twist of the shaft at B relative to A (in degrees)?
4. A torque of 9.5 kN is to be carried by a flanged bolt coupling that consists of eight 12 mm diameter steel bolts on a circle of diameter 300 mm and six 12 mm diameter steel bolts on a circle of 250 mm. Determine the shearing stress in the bolts.
A rod of length 460 mm is to be twisted by torques T until the angle of rotationbetween the ends of the rod is 3.00.a. If the allowable shear strain in the rod is 0.0006 rad, what is the maximumpermissible diameter of the rod?b. If the rod diameter is 12.5 mm, what is the minimum permissible length of the rod?
A flanged bolt coupling consists of seven steel 20mmϕ bolts spaced evenly around a bolt circle 300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress is 40MPa. See figure 13
A wide flange A60 steel column has a length of 5.8meters and pinned ends. If Sx=857x103 mm3, Sy=135x103 mm3, d=358mm, bf=171mm, A=7243mm2, Fy=414MPa, calculate the critical buckling stress, Fcr in MPa of the column. Express your answer in one decimal place.
Determine how many 18mm bolts should be used to attach a cap to a cylindrical tank with a diameter of 3.5m and a wall thickness of 16mm that is limited to a normal stress of 150MPa and the allowable stress for the bolt is 295MPa.
The lug nut on the wheel of the automobile is to be removed using the wrench and applying the vertical force of F = 30 N at A. Determine if this force is adequate, provided 14 N ⋅ m of torque about the x axis is initially required to turn the nut. If the 30-N force can be applied at A in any other direction, will it be possible to turn the nut? Solve the problem above if the cheater pipe AB is slippedover the handle of the wrench and the 30-N force can beapplied at any point and in any direction on the assembly.
Replace the loading system by an equivalent resultant force and couple moment acting point A.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends. If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (lb∙in) that may be applied at section C? pls write legibly thanks