3- (A)16 4- By Boolean Algebra YZ + (X + Z) + (XY+XZ) = Z + X. 5- OR gate produce 1 out puts when the all inputs are same. 6- (10101010) Gray equal (1100100) 2 7- AND gate produce 1 out puts when one in puts is 1. 8- (AC) 16+ (63)s equal (EF)16 9- In J-K Flip Flop will toggle on each CLK pulse when its control inputs are both HIGH. 10-Excess-3 and Gray code are non-weighted codes.

3- (A)16 4- By Boolean Algebra YZ + (X + Z) + (XY+XZ) = Z + X. 5- OR gate produce 1 out puts when the all inputs are same. 6- (10101010) Gray equal (1100100) 2 7- AND gate produce 1 out puts when one in puts is 1. 8- (AC) 16+ (63)s equal (EF)16 9- In J-K Flip Flop will toggle on each CLK pulse when its control inputs are both HIGH. 10-Excess-3 and Gray code are non-weighted codes.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. How many inputs does a full adder have? How many outputs? 2. Assume the following input levels in Figure 6-6: A4A3A2A1A0 = 01001; B4B3B2B1B0 = 00111; C0 = 0. a. What are the logic levels at the outputs of FA #2? b. What is the logic level at the C5 output?
In the given circuit, 7483 are additions and 7485 comparisons. Four-bit X and Y numbers are applied to the inputs of the circuit. In what situations would the output Q of this circuit be logic 1? A X+Y<8 ise B X+Y<7 ise C X+Y>7 ise D X+Y=8 ise E X+Y>4 ise
design a two-way traffic light system with prototype using 4-bit down counter circuit. use 7-segment as an output to represent the timer.i need help.. pls make a circuit diagram for this. (like circuit wizard and tinkercad) i will do this on the breadboarduse simple ic only like dual jk flip flopsthank you.. sorry for asking again.
show how to design a 8-bit Function Unit Combining Arithmetic Logic Unit (ALU) and a Shifter that can perform the operations given in table 1 below. Use X and Y as 8 bits input and F as 8 bits output as shown in Figure 1. S0,S1,S2 and S3 represent the selction code in the operation set table Three statue bits V (over flow), C (carry), N (negative) and are related to arrithmatic operations and statue bit Z (zero) is relataed to both arrithmatic and logic operation. Test your designed Function Unit with necessary tables.
Z output if at least two of the 4 input switches are closed (logic 1) in the logic circuit belowlogic 1, otherwise the Z output is required to be logic 0. Required minimum Z logic functionusing the Karnaugh map. (NOTE: The truth table, karnaugh map andlogic diagram is required)
This question is from the subject Digital Logic Design. Q2. Two Boolean functions are represented in the following truth table.a) Represent the function F1 and F2 in Some of Min-terms (SOM).b) Simplify both functions as Some of Products (SOP).
A fruit processing company wants to install an apple processing plant in Quetta. Company required the design of a system to pack four apples in a box but the apples vary in sizes. For simplicity an apple is characterized as ‘Big’ or ‘Small’ with logic ‘1’ and logic ‘0’ respectively. In this way there will be four categories of boxes so, a color label should be placed on each box to distinguish different boxes. The boxes should be labeled using following rule, If all four apples are small, the box should be labeled red If only two apples are small, the box should be labeled blue If only one apples is big, the box should be labeled green If all four apples are big, the box should be labeled yellow If only three apples are found big, the box should be labeled with both red and yellow. List the truth table. Draw the circuit diagram of system using decoder.
control input : cregister input : rregister output : ologic gate : OR Note: I have chosen the input and output names at random, the don't really matter. The logic gate could also be anything I just chose OR. I just want to see how everything connects together.
JOIN 3 circuits below(1,2 and 3) in a carry-ripple adder configuration and demonstrate binary addition of two three-bit numbers using a minimum of four number pairs that include both negative and positive numbers (signed 2s complement representation) and at least one overflow result. Circuit 1: a full-adder using any combination of gates from the following ICs: 7400, 7404,7408, 7410, 7420, 7432, and 7486 Circuit 2: a full-adder using a single 74138 IC and any additional assorted gates that may be necessary Circuit 3: a full-adder using a single 74138 IC and assorted gates.
Below are some more logical operations that are handled by systemsdigital, despite the input being 4 bits, we know that the output will have only one bit of result.Get system output
Behavioural Up Counter With Max Design and implement a 8-bit resetable up count, that stops counting when max is reached. The ports are: module counter( output u8_t count, input u8_t max, input logic clk, reset); The u8_t type is defined in the test bench. count is the counter's output. The counter should increment by one for even positive edge clock until the max is reached. The counter should not increment when max is reached. The counter is reset if reset = 1 when a positive edge clock occurs. The 8-bit comparator module, cmp, must be used to check when max is reached. The test bench will set max to 150 for its testing. Editor // include cmp module module counter( output u8_t count, input u8_t max,input logic clk, reset);logic m_test; cmp test(m_test, count, max); // complete the restendmodule
Please answer this question in 10 mins i will surely rate your answer. 1. A combinational circuit adds either a 1 or 2 to a 4-bit binary number A. Assume that the inputs bb A3, A2, A1, A0 represent the 4-bit binary number. Another input is a control signal C. The circuit has outputs assumed to be X3, X2, X1 and Xo, which represent the 4-bit number X. When C=0, X=A+1 and when C=1, X=A+2. Assume that the inputs for which X > (1111)2 will never occur. Show the design steps in detail including truth tables, K-Maps, logic equation minimisation. Finally, design this circuit using only NAND gates and inverters .