Q(3): Answer the followings (Only Ten)?1. In Taylor-Orowan dislocation, The amount of force required to formand move an edge dislocation is less, while speed of movement of anedge dislocation is bigger. True or False.2. Edge dislocation can move by -----, whereas Screw dislocations canmove by ------.3. The -------- is the motion of the interface between two metals thatoccurs as a consequence of the difference in diffusion rates of themetal atoms.4. Burger vector is used to denote ------- and -------- of dislocations.5. The number of frenkel defect is proportional to ---.6. Exciton can transport - without transporting7. Frankel Defect is a type of -- defect.8. As the temperature rises, the rate of vacancy diffusion in metals:a) increases, b) decreases, c) remains the same, d) may increase ordecrease.9. The following mechanism contributes very little the diffusivity.a)Vacancy, b)Interstitial, c)Substitutional, d)Self-diffusion.10. In Fick's first law the concentration is change with respect to ----inарасе.11. In the case of steel hardening by Carburization carbon permit todiffuse into iron by --12. Diffusion is driven by ------ and ------.

Name: Q(3): Answer the followings (Only Ten)?1. In Taylor-Orowan dislocatio
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: Q(3): Answer the followings (Only Ten)?1. In Taylor-Orowan dislocation, The amount of force required to formand move an edge dislocation is less, while speed of movement of anedge dislocation is bigger. True or False.2. Edge dislocation can move by

Science

Physics

3): Answer the followings (Only Ten)? 1. In Taylor-Orowan dislocation, The amount of force required to form and move an edge dislocation is less, while speed of movement of an edge dislocation is bigger. True or False. 2. Edge dislocation can move by -----, whereas Screw dislocations can move by ------. 3. The -- is the motion of the interface between two metals that occurs as a consequence of the difference in diffusion rates of the metal atoms.

3): Answer the followings (Only Ten)? 1. In Taylor-Orowan dislocation, The amount of force required to form and move an edge dislocation is less, while speed of movement of an edge dislocation is bigger. True or False. 2. Edge dislocation can move by -----, whereas Screw dislocations can move by ------. 3. The -- is the motion of the interface between two metals that occurs as a consequence of the difference in diffusion rates of the metal atoms.

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter5: Further Applications Of Newton's Laws: Friction, Drag, And Elasticity

Section: Chapter Questions

Problem 41PE: A farmer making grape juice fills a glass bottle to the brim and caps it tightly. The juice expands...

See similar textbooks

Similar questions

Let AI represent the density of aluminum and Fe that of iron. Kind the radius of a solid aluminum sphere that balances a solid iron sphere of radius rFe on an equal-arm balance.
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
A farmer making grape juice fills a glass bottle to the brim and caps it tightly. The juice expands more than the glass when it warms up, in such a way that the volume increases by 0.2% (that is, V/V0=2103 ) relative to the space available. Calculate the magnitude of the normal force exerted by the juice per square centimeter if its bulk modulus is 1.8109 N/m2, assuming the bottle does not break. In view of your answer, do you think the bottle will survive?
A vertebra experiences a shearing force, Fs = 600N. What is the magnitude of the shear deformation if the vertebra is treated as a cylinder 3 cm in height and 2 cm in radius? S = 107 N/m2.
If the following specimen is subjected to a tensile test, determine the followings: a- Young’s modulus of elasticity, if the load and extension at the limit of proportionality are 85 kN and 0.075 mm respectively. b-The stress at the limit of proportionality if the load at the limit is 85 kN. c- The ultimate tensile strength (ultimate stress), if the maximum load is 120 kN. d- The percentage of elongation, if the final length at the fracture point is 55 mm.
A steel pin inserted into a wooden member hanging from the ceiling transmitsthe loads shown in the figure. Determine: a) The crushing stress experienced by the interface between the wood and the steel. b) The shear stress experienced by the steel pin. c) The shear stress experienced by the wood.
The lintel of prestressed reinforced concrete in the figure below is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.10 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 47.5 cm2. Young's modulus for the concrete is 3.00 1010 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.45 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released(b) What is the new tension T2 in the rod?(c) The rod will then be how much longer than its unstressed length?(d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length?(e) Find the required original tension T1 in the rod.
An 80-cm-long, 1.0-mm-diameter steel guitar string must be tightened to a tension of 2.0 × 103 N by turning the tuning screws. By how much is the string stretched, in mm? The Young's modulus for steel is 20 × 1010 N/m2. Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.
A vertebra is subjected to a shearing force of 305 N. Find the shear deformation (in m), taking the vertebra to be a cylinder 3.50 cm high and 4.50 cm in diameter. (answer in m)
A tensile test was conducted by the CE 405 Construction Material and Testing course on a specimen with a diameter of 12.70 mm. A strain gage was bonded to the specimen so that the strain could be obtained directly. The following data were obtained: Microstrain - (physics) A strain expressed in terms of parts per million. Create a table of stress and strain values. Plot these data points, and draw a best-fit straight line through them. What is the slope of this line? What does this value represent?
Assume that if the shear stress in steel exceeds about 4.00 108 N/m2, the steel ruptures. (a) Determine the shearing force necessary to shear a steel bolt 1.45 cm in diameter.(b) Determine the shearing force necessary to punch a 1.05-cm-diameter hole in a steel plate 0.870 cm thick.
1. By method of sections, determine the force in member CD, CF, and FG of the Warren truss. Solve for the forces, axial stresses and the factors of safety if the member is a solid-circular cross-section that has a diameter of 30 mm and a maximum allowable stress of 10kN/m^2.