3 heat is generated inside the square shaped copper bar with a side length of 2.5 cm. What will be the surface temperature of the bar if the bar is exposed to an environment with a heat transfer coefficient at 20C and 4000W / m2C (C)

3 heat is generated inside the square shaped copper bar with a side length of 2.5 cm. What will be the surface temperature of the bar if the bar is exposed to an environment with a heat transfer coefficient at 20C and 4000W / m2C (C)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.38P: 2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from...

See similar textbooks

Similar questions

A 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to the rod with an inner diameter of 35 mm and an outer diameter of 110 mm. This creates an air gap between the fuel rod and the hollow ceramic cylinder with a convective heat transfer coefficient of 10 W/m²·K. The hollow ceramic cylinder has a thermal conductivity of 0.07 W/m·K and its outer surface maintains a constant temperature of 30 °C. If the fuel rod generates heat at a rate of 1 MW/m³. Solving, the temperature at the surface of the fuel rod is 1026°C. I need the solution with fundamental concepts (Textically with definitions) of how the heat flow behaves in the system. NOT THE MATHEMATICAL RESOLUTION. I already know how to solve it.
A 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to the rod with an inner diameter of 35 mm and an outer diameter of 110 mm. This creates an air gap between the fuel rod and the hollow ceramic cylinder with a convective heat transfer coefficient of 10 W/m²·K. The hollow ceramic cylinder has a thermal conductivity of 0.07 W/m·K and its outer surface maintains a constant temperature of 30 °C. If the fuel rod generates heat at a rate of 1 MW/m³. Solving, the temperature at the surface of the fuel rod is 1026°C. Explain how the heat flow behaves in the system, using the fundamental concepts.
A 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to the rod with an inner diameter of 35 mm and an outer diameter of 110 mm. This creates an air gap between the fuel rod and the hollow ceramic cylinder with a convective heat transfer coefficient of 10 W/m²·K. The hollow ceramic cylinder has a thermal conductivity of 0.07 W/m·K and its outer surface maintains a constant temperature of 30 °C. If the fuel rod generates heat at a rate of 1 MW/m³. Solving, the temperature at the surface of the fuel rod is 1026°C. Give the solution from fundamental concepts of how the heat flow behaves in the system.
A 15 mm diameter cylindrical nuclear fuel rod is housed in a hollow ceramic cylinder concentric to the rod with an inner diameter of 35 mm and an outer diameter of 110 mm. This creates an air gap between the fuel rod and the hollow ceramic cylinder with a convective heat transfer coefficient of 10 W/m²·K. The hollow ceramic cylinder has a thermal conductivity of 0.07 W/m·K and its outer surface maintains a constant temperature of 30 °C. If the fuel rod generates heat at a rate of 1 MW/m³. Determine the temperature at the surface of the fuel rod. Note: Give the solution from fundamental concepts of how the heat flow behaves in the system
2. A 15-cm X 20-cm hot surface at 85°C is to be cooled by attaching 4 cm-long aluminum (k = 237 W/m-°C) fins of 2-mm X 2-mm square cross section. The temperature of surrounding medium is 25°C and the heat transfer coefficient on the surfaces can be taken to be 20 W/m2-°C. If it is desired to triple the rate of heat transfer from the bare hot surface, determine the number of fins that needs to be attached.
Convective heat transfer coefficient is 15 W/(m*K), surface area of the fin is 2 m^2, the temperature at the base is 70 C and the ambient temperature is 20 C. Determine the fin efficiency if the actual heat transfer rate from the fin is 500 W? not sufficient information 66 % none of the given 15 % 33 %
Determine the resistance (in F-h/BTU) of a hollow cylinder with an inside and outside radius of 2 in and 2.1 in, respectively. The length of the cylinder is 3 ft while the thermal conductivity is 24 BTU/hr-ft-F. Correct Answer: 1.0784994169E-4 ± 1%
The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k= 240 W/m·K) or copper (k= 390 W/m·K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C and heat is transferred from the stove to the pan at a rate of 1200 W. What is the temperature of the surface in contact with the stove for each of the two materials?Aluminum:T= _____ °CCopper:T= _____ °C
A hot surface at 100°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m·K) to it, with a center-to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m2 ·K. Determine the rate of heat transfer from the surface for a 1-m x 1-m section of the plate. Also determine the overall effectiveness of the fins.
A 2 m X 1.5 m section of wall of an industrial furnace burning gas is not insulated, and the temperature at the outer surface of this section is measured to be 80oC. The temperature of the furnace room is 30oC, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 w/oC. It is proposed to insulate this section of the furnace wall with glass wool insulation (K=0.038 W/moC) in order to reduce the heat loss by 90 percent. Assuming the outer surface temperature of the section remains at about 80oC, determine i) the thickness of the insulation that is needed and ii) the outer surface temperature of the insulation after installation.
Determine the temperature variation inside the iron plate with a thickness of 1.5 mm, cross-sectional area of 310 cm^2, convection heat transfer coefficient of 11 W/(m^2K), room temperature of 18 C. The electrical power required to operate the iron is 2 kW and the thermal conductivity of the iron is 21 W/(mK). -3072x+5888 -2517x+5412 5888x-3072 none -5412x+2517
12. A 3.1 cm long straight rectangular fin has a thickness of 2.7 mm. The thermal conductivity is 52 W/m K. The fin is attached to a wall maintained at 190 °C and is exposed to a convection environment at 40 °C and h- 31 W/m2 K. What is the fin efficiency? Express your answer in percent.