3 (i) A 10 kg block on an inclined plane is attached to a spring with a spring constant of k = 200 N/m (see Figure 3.1). Assume that the block is released from rest and from a position at which the spring is not stretched or compressed. (a) In the absence of friction, calculate the distance covered by the block from the initial position to the position where it stops first. State your assumptions and comment on your solutions. (b) Assume that there is friction between the block and inclined plane, with kinetic friction coefficient μ = 0.3. Calculate the distance covered by the block from the initial position to the position where it stops first. State your assumptions and comment on your solutions. 00000 k = 200 N/m Figure 3.1 30°

3 (i) A 10 kg block on an inclined plane is attached to a spring with a spring constant of k = 200 N/m (see Figure 3.1). Assume that the block is released from rest and from a position at which the spring is not stretched or compressed. (a) In the absence of friction, calculate the distance covered by the block from the initial position to the position where it stops first. State your assumptions and comment on your solutions. (b) Assume that there is friction between the block and inclined plane, with kinetic friction coefficient μ = 0.3. Calculate the distance covered by the block from the initial position to the position where it stops first. State your assumptions and comment on your solutions. 00000 k = 200 N/m Figure 3.1 30°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
A small particle with mass m is tied to a light rod (assume no mass) with length l.The rod is tied at the other end with a ball and socket joint with no friction. The rod is held in place in a horizontal position with a spring. The spring has a stiffness coefficient of k. Parallel to the spring is a dashpot. The rod is then pulled down below the equilibrium point, such that the rod creates an angle theta with the equilibrium point. The rod is held in this place before being released. Decide the damping coefficient c such that the oscillation will be a critically damped oscillation
quick Problem 5. A F = 2 N Slider AC of mass 0.5 kg moves along a frictionless -> horizontal guide under the action of a constant force F = 2N. A uniform slender rod AB of mass 0.25 60° kg and length 1 m is pinned to slider AC by means of a frictionless pin at point A and a thin wire at point B. Find the tension in the wire when released from wire rest. Ans: Ax = 0.1460, Ay = 1.5507, T = 1.0413 Newtons B.
2.0 kg push 45° Problem 4: (a) The 2 kg wood box in the Figure above on the left slides up a vertical wood wall while you push on it at a 45° angle. The coefficient of kinetic friction for wood on wood is Hk = 0.2. What magnitude force Fpush should you apply to cause the box to slide up at a constant speed? Recall that constant speed means a = 0 m/sec?. Answer: 34.6 N. (b) Let's re-do part (a), but with the box now sliding down the vertical wood wall while you push on it at a 45° angle. Hk is still Hk = 0.2. What magnitude force Fpush should you apply to cause the box to slide down at a constant speed? Recall that constant speed means a = 0 m/sec?. Answer: 23.1 N. Problem 5: The Figure shows two blocks connected by a cord (of negligible mass) that passes over a frictionless pulley (also of negligible mass). The arrangement is known as Atwood's machine. One block has mass mi = 1.3 kg; the other has mass m2 = 2.8 kg. What are: (a) The magnitude of the blocks' acceleration. Answer: 3.6…
Figure below shows a mass-spring model of the type used to design packaging systems and vehicle suspensions, for example. The springs exert a force that is proportional to their compression, and the proportionality constant is the spring constant k. The two side springs provide additional resistance if the weight W is too heavy for the center spring. When the weight W is gently placed, it moves through a distance x before coming to rest. From statics, the weight force must balance the spring forces at this new position. (if x=d) These relations can be used to generate the plot of x versus W. (a) The following values are given: k1=104 N/m; k2 = 1.5 *104 N/m; d =0.1 m. Create a function that computes the distance x, using the input parameter W; Then, test your function for the following two cases, using the values: W=500 N W=2000 N. (b) Create another script and use your function to plot x versus W for 0 < W < 3000 N for the values of k1, k2, and d given in part a.
Problem #1 A student pushes the 1.25 kg block in the figure below against a horizontal spring, compressing it by 0.175 m. k x = 0 *max ! v=0 y=0 The left end of a horizontal spring is attached to a vertical wall, and when released, the block travels across a horizontal surface and up an incline. Neglecting friction, find the block's maximum height (in m) if the spring constant is k = 645 N/m. (The acceleration of gravity is g = 9.80 m/s².)
Problem A block with a mass of 15 kg sits on the smooth incline shown below where the angle is e = 37°. The block is attached to the wall via a spring with a spring constant of k = 246 N/m. The coordinate system for this problem is oriented as shown in the diagram. Based on this information, answer the following: a) Determine the distance the spring must stretch to offset the weight component of the block in the x-direction (this is where your x-direction datum will be located). b) Create a free body diagram and use the force balance in the x-direction to develop the second-order ordinary differential equation governing the motion of the block (your force balance should be based upon the datum found in part a). c) Find the natural frequency (wn), the period of vibration (T), and the frequency (f). d) For an undamped, freely vibrating system the solution to the second-order ordinary differential equation developed in part b has the form x(t) = Asin(wnt) + Bcos(wnt). If at time t = 0 s…
A 30kg mass is tied to a uniform rod whose mass and length are 80-kg and 8-m, as shown below. The rod is attached to the floor via a hinge and makes an angle of 70° relative to the ground; a massless string is also attached to the rod at the ¼ point of the rod and makes an angle of 20° relative to the horizontal. What tension must be provided by the rope so that the system remains in stationary? If at some point the string breaks, what will be the angular acceleration of the system the instant that the string breaks?
Consider the system of two blocks shown in (Figure 1). There is no friction between block A and the tabletop. The mass of block B is 4.80 kg. The pulley rotates about a frictionless axle, and the light rope doesn't slip on the pulley surface. The pulley has radius 0.200 m and moment of inertia 1.30 kg⋅m2. If the pulley is rotating with an angular speed of 8.00 rad/s after the block has descended 1.20 m, what is the mass of block A?
5. There are two masses with unequal weight. The masses are tied by a rope and they are connected over two pulleys as shown in Figure 1. When the system is released, heavier mass accelerates downward and lighter accelerates upward. Assume frictionless pulleys, find the theoretical tension of the thread and the theoretical acceleration. Masses are M1= 6.00 kg and M2= 2.00 kg. Two discs are allowed to move on inclined air table with dimensions a= 11cm, b=17cm, c=60cm. (Hint: You can use free body diagram and M1 b Newton' W.B. M2 s second law of a motion equation (F=m.a) to solve tension, g=980cm/s?.)
The Figure Q2 shows a ball and block with masses M1=10kg and M2, respectively. The block and ball are connected with a cable and pulley system. The coefficient of static friction for all contacting surface is 0.3. i) Determine the range of the mass of block so that the system is in M1 = 10 Kg equilibrium. ii) Determine the tension in the cable. M2 Hs= 0.3 Comment on your answer at question 2(i). 75%