3 m mm 8@1.8m = 14.4m The bottom chord of the truss is composed of 2 Nos. ISA 60 x 60 x 6 with gusset thickness of 10 mm (back to back and both sides of the gusset). Calculate the factored load carrying capacity of the member under compression only. (ISA 60 × 60 × 6 : A = 684 mm², lxx = lyy= 226000 mm4, Cxx = Cyy = 16.9 mm) 80 90 100 110 120 130 140 150 KL/r fcd (MPa) 118 105 92.6 82.1 73 65.2 58.4 52.6 Longitudinal ties are provided at alternate node of the bottom chord.

3 m mm 8@1.8m = 14.4m The bottom chord of the truss is composed of 2 Nos. ISA 60 x 60 x 6 with gusset thickness of 10 mm (back to back and both sides of the gusset). Calculate the factored load carrying capacity of the member under compression only. (ISA 60 × 60 × 6 : A = 684 mm², lxx = lyy= 226000 mm4, Cxx = Cyy = 16.9 mm) 80 90 100 110 120 130 140 150 KL/r fcd (MPa) 118 105 92.6 82.1 73 65.2 58.4 52.6 Longitudinal ties are provided at alternate node of the bottom chord.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude of the force (lb) in member BD of the truss shown if P = 32793 lb, Q = 33403 lb, and y = 6.6 ft. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate whether the force is tensile or compressive: use T if tensile and C if compressive.
Determine forces in members JK, KD, and DE and state whether in compression or tension Ax=0 Ay=6 kip up Gy=6kip up
26 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Ax = ?A) 30B) 18.75C) None.D) 3.75E) 0
Determine the force in member EG, and indicate whether the members are in tension or compression. if P=11kN. 24.75kN (T) 24.75kN (C) 39.66kN (T) 39.66kN (C) 41.25kN (T) 8.25kN (C) 8.25kN (T) 41.25kN (C) ORONORCORORORORC
The length of top chord from A to Dis 24 m which is equally divided by 4 spons Determine the value of forces of the following members and identify if T or C: FN = 95 kN MN = 86 kN SN = 79 KN
For the truss shown, determine the force in members BD, CD, and CE stating whether the member force is in tension or compression. Wherein: Q=2 T=6 Example: 2QT kN = 226 kN T.Q5 m = 4.25 m
The T section shown is formed by joining two rectangular pieces of wood together. The beam is subjected to a maximum shearing force of 60 kN. All dimensions are in mm . A.) Which of the following gives the moment inertia in x 10^6mm^4 at the neutral axis? Choices: 8.56,14.26,10.57,21.52 B.) Which of the following gives the shearing stress at the neautral axis? Choices: 3.21,4.64,3.95,4.28 C.) Which of the following gives tge shearing stress in MPa at the junctiin between two pieces of wood? Choices: 31.78,21.42,28.32,16.52
Find the value of EI · ? at the center of the last span of the beam.
For the type 1 compound truss shown inthe figure, determine the force in each memberand state if the members are in tension orcompression. The internal angle between anytwo members is 60°. The truss is pin supportedat A and roller supported at F.x = 5y = 0
Three rods each with area of 250 mm² jointly supports a 9.5 kN load. Assume that there was no slack stress in the rods before the load was applied. E(steel) = 200 GPa, E(bronze) = 83 GPa. The steel supports the load vertically while the two bronze are opposite each other inclined at an angle 30 from the vertical forming a triangle to the common support.1. Find the load carried by the steel rod if it is 3 meters long. a. 3.236 kNb. 5.124 kNc. 6.174 kNd. 6.147 kN2. Find the stress in each bronze rod. a. 6.78 MPab. 7.68 MPac. 5.4 MPad. 7.10 MPa3. Find the elongation of the steel bar. a. 0.370 mmb. 0.124 mmc. 0.356 mmd. 0.427 mm
For the type 2 compound truss shown inthe figure, determine the force in each memberand state if the members are in tension orcompression. Trusses ACE and BDF are connectedby three bars, BE, CD, and DE. Dimensions inmeters.x = 5y = 0
Given the truss below, find the tension connected at pin D then find the forces in members BD, CD andCE using method of sections. 5m 5m 5m 5m 5m 5m 30kN 20kN