The beam is shown below. a. Sketch the qualitative influence lines for the support reaction at A and C, moment at A, shear and moment at C. Place all important ordinates and dimensions in the sketch. b. If the beam is loaded with uniform dead load 4 kN/m, uniform moving load of 10.25 kN/m and a concentrated live load of 112 kN, determine the maximum reaction at A, maximum shear at C, and maximum bending at C due to these loads? A 4m 3m 2m

The beam is shown below. a. Sketch the qualitative influence lines for the support reaction at A and C, moment at A, shear and moment at C. Place all important ordinates and dimensions in the sketch. b. If the beam is loaded with uniform dead load 4 kN/m, uniform moving load of 10.25 kN/m and a concentrated live load of 112 kN, determine the maximum reaction at A, maximum shear at C, and maximum bending at C due to these loads? A 4m 3m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 6 m long beam above is subjected to a point force of 15 kN at an angle of θ = 60°, a clockwise couple moment of 20 kN·m, and a constant distributed load of 10 kN/m as shown. It is pinned at A and has a roller at B. Neglect the weight of the beam. A. Determine the support reactions at pin A and roller E. B. The shear force between A and B is: C. The shear force between B and C is: D. The shear force between C and D is: E. The shear force between D and E is: F. The moment between A and B is: E. The moment between B and C is: F. The moment between C and D is: G. The moment between D and E is: H. Sketch shear force chart. I. Sketch moment diagram.
A 5 m long cantilever beam carries a uniform load of 5 KN/m on the 3 m portion of the beam from the free end and a counterclockwise couple of 60 KN -m acting at 1 m from the fixed support. Which of the following nearly gives the value the vertical reaction at the fixed point in KN and the value of the moment at midspan? Vertical fixed point: a. 15kn b. 20kn c. 5kn d. 10kn moment at midspan a. 22.5kn b. 45kn c. 15kn
Given : M1 = 400 kN-m M2 = 500 kN-m M3 = 600 kN-m P = 150 kN w1= 60 kN-m w2 = 120 kN/m a = b = d = 6 m c = 4 m Determine the following: a. The maximum positive shear (in kN). b. The maximum negative shear (in kN). c. The maximum positive moment (in kN-m). d. The maximum negative moment (in kN-m). e. The location of maximum shear from the left end of the beam (in m). f. The location of the maximum moment from the left end of the beam (in m). Kindly Draw the Shear and Moment Diagram. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
In the beam shown, take P1 = 4 kN, P2 = 7 kN, and W1 = 5 kN/m. a) Determine the vertical reaction at "A" b) Determine the vertical reaction at "B" c) Determine the shear at X1 d) Determine the shear at X2 e) Determine the moment at X2
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
For the beam shown below, the maximum negative shear and the maximum negative bending moment at point D due to the wheel loads of the moving vehicle are -19.7 kN and -60.25 kN.m, respectively. Determine the wheel loads P1 and P2. The vehicle travels towards the right. Joint A is a roller and joint E is a fixed support.
If the beam carries a moving uniform load of 1.19kN/m and concentrated moving load of 114 kN as indicatedin the figure. Using the influence line diagram, (a) determine the max. moment due to loads at C (b) determine max positive V at C
1.) What is the vertical reaction at A and B?2.) What is the horizontal and moment reaction B3.) What is the maximum positive moment in the beam?(kN-m)4.) What is the location of the maximum positive moment from point A? (m) 5.) What is the shear at a point between A and C?6.) What is the moment at a point under the concentrated load?
GIVEN: L1 = 4.5 m W1 = 10 kN/m L2 = 1.2 m W2 = 12 kN/m L3 = 0.5 m L4 = 12 m L5 = 1.5 m A. What is the maximum shear in Beam D-E-B? B. What is the maximum moment in Beam A-B-C?
a. What is the absolute maximum shear in the beam? (in kN) b. What is the location of the absolute maximum shear from the left end of the beam? (in m) c. What is the absolute maximum moment in the beam? (in kNm)
The beam in the figure below is to be loaded with 32.2 kN single axle load, a uniformly distributed live load of 49 kN/m, and a uniformly distributed dead load of 22 kN/m. Considering the loads, draw the influence lines and determine the following. - Maximum Vertical Reaction at C in kN - Maximum Negative Shear at B in kN. - Maximum Positive Shear at B in kN. - Maximum Positive Moment at B in kN-m.
1. what is the maximum moment in the beam? answer in KN-m 2. what is the maximum shear in the beam? what is the highest shear force at 6m? (kN) 3. what is the shear force at the free end of the beam? 4. what is the highest shear force at 6m? (kN 1Decimal point)