3) Solve for all the reactions on the structure below. Express all answers in x and y components as discussed in class. Show all directions as assumed prior to starting the problem and the final directions. Do not leave as number of significant figures for internal calculations and final answers. or +. Use the proper 100k 207 KFT 100 00

3) Solve for all the reactions on the structure below. Express all answers in x and y components as discussed in class. Show all directions as assumed prior to starting the problem and the final directions. Do not leave as number of significant figures for internal calculations and final answers. or +. Use the proper 100k 207 KFT 100 00

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

GIVEN: L1=20 N GIVEN: a= 4m GIVEN: L2= 20 N GIVEN: b= 5m GIVEN: L3=20 N GIVEN: c= 6m GIVEN: L4= 0 N GIVEB: e= 3m GIVEN: L5= 10 N ANSWER: (a) Ax in N (b) Ay in N (c) Ex in N (d) Ey in N PLS SOLVE IN A COMPLETE SOLUTION AND WRITE LEGIBLY AND ALSO DRAW THE FREE BODY DIAGRAM
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 1. A spherical tank for storing gas under a pressure is 20 m in diameter and is made of steel 20 mm thick. The yield point of the material is 240 MPa. If a factor of safety of 2 is desired, what is the maximum permissible internal pressure that the tank can hold?
A single bar has 3 different cross sections as shown below. The load P1 is equal to 25,500 Newtons and P3 is equal to 17,000 Newtons. Determine the reaction at the support at bar (3). Find the force in bar (2). Note: Final Answer in 4 decimal places.
A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was 10 N. The thickness of the metal is twice its L. Using the formula on the three-point test of materials, compute for the thickness of the metal in centimeters.
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget FBD and show me your step Please make sure your answer is correct please p1=123 p2=12
P = 80 kN σt = 150 MPa t = 8.0782 mm Can you help me solve for d2?
A Japanese steel manufacturer is considering expanding operations. From experience, it estimates that new capacity additions obey the law f(y) = .00345y.51,where the cost f(y) is measured in millions of dollars and y is measured in tons of steel produced. If the demand for steel is assumed to grow at the constant rate of 8,000 tons per year and future costs are discounted using a 10 percent discount rate, what is the optimal number of years between new plant openings?
The S-N curve which represents the fatigue strength, which is measured as a stress amplitude, as a function of number of stress cycles, can be approximated by a straight line in therange of 103cycles to 106cycles when plotted as log(S) versus log(N). Beyond 106cycles,the fatigue strength remains constant. The fatigue strength of a certain alloy at 103cyclesis given as 80 % of the ultimate tensile strength and its endurance limit is 50 % of theultimate tensile strength.(a) The alloy part fails in 15 000 cycles. Calculate the percent change (increase or decrease)of the maximum applied cyclic stress amplitude if the life of the part needs to beextended by 3.5 times. Is this considered under a high or low cycle fatigue failure?State any assumptions made. (12 marks)(b) If the applied cyclic stress amplitude remains unchanged when the life is extended by3.5 times, calculate the percent change (increase or decrease) of the ultimate tensilestrength of a new alloy required. (8 marks)(c) If the…
1. A cable used to lift heavy materials can resist breaking even under a load of 1 meganewtons. The steel cable must support twice that load for safety purposes. By how much the steel cable will stretch if it carries 1 meganewtons of load? Assume 8.0 m initial length of the cable. 2. Ships and sailing vessels often carry lead ballast in various forms, such as bricks, to keep the ship properly oriented and upright in the water. Suppose a ship takes on cargo and the crew jettisons a total of 0.500 m3 of lead ballast into water 2 000 m deep. Seawater's density is equal to 1.025 g/cc while lead's bulk modulus equals to 42.0 GPa. Calculate the weight of water in a column with cross section of 1.00 m2. Find the change in the pressure at 2.0 km depth. Find the change in the volume of the lead at 2.0 km depth.
A spherical ball of copper having the original Surface area of 20. 58 mm2 and deformed until the surface area becomes 12.57 mm2. By Using the following graphs, find the tensile strength and ductility.
16. There are 4 materials that were exposed to different forces and their corresponding elongation is given. Which will have the greatest and lowest value of k. Material A was exposed to 100 N force and elongation is 0.02 meters. B was exposed to 200 N force and elongation is 0.05 meters. C was exposed to a force of 300 N and elongation is 0.07 meter, D was exposed to 400N force and elongation is 0.09 meter.