3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. - 21

3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. - 21

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.33P

See similar textbooks

Similar questions

2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
Consider a material that can be altered with exposure to an electric field such that it undergoes a structural transition from an insulator (state) to an electrical conductor (state) when the field is applied. The material in both its insulator and conductor states has a phonon contribution to its thermal conductivity of ? = 2 W/m·K. What is the thermal conductivity of the material with and without an applied electric field? ( electrical resistivity is ????? = 1x10-6 m/S at ? =27C with an applied electric field)
In a multilayered rectangular wall, the thermal resistance of the first layer is 0.005 °C/W, the resistance of the second layer is 0.2° C/W, and for the third layer it is 0.1 ° C/W. The overall temperature gradient in the multilayered wall from one side to another is 70° C. a. Determine the heat flux through the wall. b. If the thermal resistance of the second layer is doubled to 0.4° C/W, what will be its influence in % on the heat flux, assuming the temperature gradient remains the same?
The heat loss per hour through 1 sq. ft of furnace wall 18" thick is 520 Btu. The temperature on the hot side of the wall is 1900 degrees F, and its average thermal conductivity is 0.61 Btu/hr-ft-°F. Determine the temperature on the other side of the wall in °C.
You are asked to determine the heat loss from a very thin spherical cap containing a hot fluid at a temperature of 140.0°C. The outside diameter of the cap is 40.0 m and it is insulated by three layers of insulation of thickness 50.0 m each. The thermal conductivities of each layer are:?1 = 0.02 ?⁄??; ?2 = 0.06 ?⁄??; ?3 = 0.16 ?⁄?? These thermal conductivities are indicated from the inside out in the spherical space coordinate. On the other hand, the external temperature of the system is 30.0°C. Additionally, you are asked to determine the temperatures at the contact interfaces between the different materials. Finally, you are asked to make a freehand diagram of the system, indicating the temperatures obtained by you for each interface and the heat flux.
The furnace wall shown in the figure is made of a material with a thermal conductivity of 5 W / m ° C, the radiant emission coefficient of the outer surface of the wall is 0.95, Stefan Boltzman constant is 5.67x104 W / m ^ 2 (K ^ 4), ambient temperature and air temperature 297 K is. The heat transfer coefficient between the outer surface of the wall and the air is h = 20 W / m (K ^ 2). Wall inner surface temperature 573 K, outer surface temperature 308 K Since the value is kept constant a) Find the layer thickness of the wall? b) Find the layer thickness of the wall if the moving fluid medium on the outer surface of the wall is corroded?
A coil-shaped cooling pipe is made of SS-304 material. This pipe is 1 ft long, 0.4 inch outside diameter, and inch inside diameter. This coil cooling pipe is used to cool the water in the bath. The temperature of the inner coil pipe is 40oF while the outer coil in contact with water is 80oF. The thermal conductivity of SS-304 is a function of temperature where k(T) = 7.75 + (7.78 x 10-3).T where k is in Btu/h.ft.oF and T is in oF. Calculate the rate of heat dissipation in watts! (1287.7)
A 2 m X 1.5 m section of wall of an industrial furnace burning gas is not insulated, and the temperature at the outer surface of this section is measured to be 80oC. The temperature of the furnace room is 30oC, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 w/oC. It is proposed to insulate this section of the furnace wall with glass wool insulation (K=0.038 W/moC) in order to reduce the heat loss by 90 percent. Assuming the outer surface temperature of the section remains at about 80oC, determine i) the thickness of the insulation that is needed and ii) the outer surface temperature of the insulation after installation.
‏Q1 / A5 - cm - diameter steel pipe is covered with a 1 - cm layer of insulating material having k = 0.22 W / m . ° C followed by a 3 - cm - thick layer of another insulating material having k = 0.06 W / m . ° C . The system is exposed to a convection surrounding condition of h = 60 W / m² . ° C and T -15 ° C . The outside surface temperature of the steel pipe is 400 ° C . Calculate the heat lost by the pipe - insulation assembly for a pipe length of 20 m . Express in Watts .
A 2-m × 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m2·C. It is proposed to insulate this section of the furnace wall with perlite insulation (k = 0.052 W/m·C) in order to reduce the heat loss by 90 percent, Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used.
The wall of a furnace consists of 200 mm thick refractory brick (k = 3 Btu / hr-ft2-0F), 100 mm thick bricks (k = 0.050 Btu / hr-ft2-0F) and 6 mm thick steel. The temperature on the side of the refractory brick layer of the furnace is 1150 C, and the temperature on the outer steel surface is 30C. There is a heat loss of 300 W / square meter at the wall of the furnace. It is difficult to prevent the thin air additions between the brick layers and the brick layer and the steel wall. How many mm of brick layers is the total thickness of these air layers equivalent?
A 2-m x 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m² • °C. It is proposed to insulate this section of the furnace wall with expanded perlite insulation (k = 0.052 W/m • °C) in order to reduce the heat loss by 90%. Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used. ANSWER:_______cm