3) Two hemispherical shells are bolted together as shown in the figure. The resulting spherical container, which weighs 300 lb, is filled with mercury and supported by a cable as shown. The container is vented at the top. If eight bolts are symmetrically located around the circumference, what is the vertical force that each bolt must carry? Cable Vent Sphere diameter 3 ft A) 1980 lb B) 1890 lb C) 1980 k D) 1890 k

3) Two hemispherical shells are bolted together as shown in the figure. The resulting spherical container, which weighs 300 lb, is filled with mercury and supported by a cable as shown. The container is vented at the top. If eight bolts are symmetrically located around the circumference, what is the vertical force that each bolt must carry? Cable Vent Sphere diameter 3 ft A) 1980 lb B) 1890 lb C) 1980 k D) 1890 k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cable is attached to a 2.20 kg block A, is looped over a fixed peg at C, and is attached to plate B.(Figure 1) The coefficient of static friction between the plate and the block is μA= 0.180, the coefficient of static friction between the plate and the inclined plane is μB = 0.380, and the coefficient of static friction between the cable and the peg is μC= 0.450. If the plane's angle is 30.0 degrees, what is the maximum mass that plate B can have such that it does not slide down the plane?
The system in the figure is in balance. A load of 1600 kg is suspended frompoint C on the cable connected from points A and B. The relevant distances areclearly given in the figure. In this case, calculate the forces in the AC and BC cables.24- Force on AC cable? (kg)25- Force, BC in cable? (kg)
A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1
As shown, a gate has a parabolic shape that follows the equation y=C?32x2, where C = 6.00ft . (Figure 2) The top of the gate is d = 2.10ft beneath the water's surface. What is FR, the magnitude of the force exerted on the gate by the water? The gate's width (perpendicular to the image) is b = 6.50ft and the water's specific weight is ?w = 62.4lb/ft3 .
From the given figure of a cable connection shown: Determine the tension (in kN) in segment CD. Use F1 = 12 kN, F2 = 21 kN, a = 2.6 meters, b = 2.43 meters, c = 1.49 meters, y = 2.61 meters. Round off to two decimal places.
A 209.9N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC which lies in a vertical transverse plane and loops underneath the shaft. Calculate the tension T1 (N) in the cable. Round off only on the final answer expressed in 3 decimal places.
A block having a mass of m = 16 kg is suspended via two cables as shown in the figure. The angles shown in the figure are as follows: α = 19° and β = 35°. We will label the tension in Cable 1 as T1 and the tension in Cable 2 as T2. 1) solve for the numeric value of T1 in newtons.. 2.)solve for the numeric value of T2 in newtons..
The 32kg mass is suspended from three cables. Cable AC is equipped with a turnbuckle so that its tension can be adjusted and a strain gauge that allows its tension to be measured. If the tension in cable AC is 46N, what are the tensions in cables AB and AD?
Two blocks are connected by a light, flexible cable that passes a frictionless pulley. Block A weighs 500N and block B weighs 200N. The coefficient of static friction between A and the ramp is 0.30. Determine: (a) If the motion is impending down the plane, what is the tension force in the cable connecting Block A and Block B. (b) Are the two block in equilibrium state? 3 dec places pls
Please answer question number 6 and show your complete solution. Thank you very much. 5. Two locomotives on opposite banks of a canal pull a vessel moving parallel to the banks by means of two horizontal ropes. The tensions in these ropes are 2000 N and 2400 N while the angle between them is 600. Find the resultant pull on the vessel and the angle between each of the ropes and the sides of the canal. 6. Rework problem # 5 if the cable tensions are 2000 lb and 1500 lb
The cable supporting an elevator with a mass of 5000kg is to bedesigned so that the maximum acceleration is 0.8m/ . What are themaximum and minimum forces the motor should exert on the supportingcable? Include the given and figure
The block with a mass of 500 kg is kept in equilibrium. Calculate the magnitude of the force T pulling the cable. Thank you in advance,