Given a system shown in the figure below, a bar is mounted firmly on the ground with a distributed load applied on it. 3 m 10 N/m 45° 5V2 m Bar Ground Based on the information given in the figure, draw a single point load accompanied by its magnitude in the figure below, so that the ground experiences the same loading from the bar, 3 m 5V2 m

Given a system shown in the figure below, a bar is mounted firmly on the ground with a distributed load applied on it. 3 m 10 N/m 45° 5V2 m Bar Ground Based on the information given in the figure, draw a single point load accompanied by its magnitude in the figure below, so that the ground experiences the same loading from the bar, 3 m 5V2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1. What is the shear at E? 2. What is the shear and moment at point C? 3. What is the shear and moment at point A? please provide a solution, thank u so much.Given: Shear and moment at left of C Vc= -4.5 kn Mc= -4.5 kn-m Shear and moment at right of C Vc= 37.5 knMc= -94.5 kn-m
An engineer used a 100m tape measuring an inclined distance. The measured length on the slope was recorded to be 659.2m long. The difference in elevation between the initial point and end point was found to be 3m. The 100m tape is of standard length at a temperature of 12℃.and a pull of 50N during the measurement the temperature reading is 25℃. And the tape was supported at both ends with an applied pull of 75N if A = 6.75mm^2, E= 200Gpa; mass of tape is 0.085kg/m, k= 0.0000116/℃.Find:a. Total correction per tape lengthb. The corrected slope or total lengthc. The horizontal distance
d(mm)=125 q(kN/m)=3.0 F(kN)=2.0 T allow(MPa)= 2.5
The boom OAB pivots about point O, while section AB simultaneously extends from within section OA. Determine the velocity and acceleration of the center B of the pulley for the following conditions: θ = 19°, θ˙ = 6 deg/sec, θ¨ = 2 deg/sec2, l = 6 ft, l˙ = 2.1 ft/sec, l¨ = -3.1 ft/sec2. The quantities l˙ and l¨ are the first and second time derivatives, respectively, of the length l of section AB. Express your answers as vectors in the er and eθ directions.
-Problem XYZ. A steel tape is 100 m long at a standard pull of 65 N. Compute the pull correction in mm if during measurement the applied pull is 40N. The tape has a cross sectional of 3.18 mm^2 and E=200GPa. If the measured length of the line is 865.30, what is the corrected distance? CHOICES: A. 3.93MM, B. 3.94MM, C. 3.95MM, D. NONE OF THE ABOVE -On Problem XYZ. If the measured length of the line is 865.30, what is the corrected distance? CHOICES: A. 865.266, B. 865.301, C. 865.27, D. NONE OF THE ABOVE
If F1 = 10N, F2 = 15N, F3 = 8N, F4 = 10N, F5 = 18N, and the length of te side of a red square is 1m. Calculate magnltude (+ for CCW, - for CW) of the resuItant moment (N-m) about point A.
For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the shear diagram of the line from B to C?A.15 KN/mB.16 KN/mC.24.46 KNmD.11.26 KNmThe change in moment [KNm] of the diagram above from point A to the concentrated load is nearest toA.98B.99C.100D.101
Home Work H.W(l Blocks A.B and C have weights of 50N.25N and 15N respectively. Determine the smallest horizontal force P that will cause impending motion. The coefTicient of static friction between A and B is p=0.3, between B and C is H=0.4. and between block C and the ground is p=0.35.(Ans: P=45N)
Use a = 44.1 kN and b = 18.3 kN. Enter absolute value only.
Fast pls solve this question correctly in 5 min pls I will give u like for sure Mnty Find the moment of inertia of a plate covering the region bounded by -6x, 6x, y=0, and y =1with respect to the x-axis.
A line was recorded as 1750.00 meters long. The standard tape weighs0.65 kg , 30.00m long at 20°C under a 50N pull. During the actualobservation the temperature was 5°C and the tape was suspended undera 75N pull. It was also found that the tape is 3.00mm too long. If the linewas inclined at 3%. E = 200GPa, A = 2.50mm² and the coefficient of linearexpansion is 0.0000116 m/°C.(a) What is the actual inclined distance?(b) What is the actual horizontal distance.
hi im stuck in this please help me out A wooden beam is loaded by a concentrated load ?P = 5000 N and supported by boundary conditions as shown in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that ???LAB = 3000 mm, ???LBC = 2000 mm, ?0B0=10 mm, ?1B1 = 30 mm, and ?H = 240 mm, ℎ0h0=200 mm, ℎ1h1=20 mm, determine the following quantities below: last two sub parts of question didnt fit in so i will type here- theres no question d e) Determine the maximum magnitude of shear force and bending moment, neglecting the sign. The maximum magnitude of internal shear force, positive value: N The maximum magnitude of internal bending moment, positive value: N*mm f) Determine the magnitude of the maximum bending stress in the beam, neglecting the sign. Maximum bending stress, positive value: MPa