Solve correctly please, with detailed explanation required. 3- What is the volumetric flow rate at point 3 in the following pipe system?a)3b) 0.30.5UDOG1005V₁ = 10 m/sA1 =0.59²²1A3=0,3m²2V₁ = 4 m/sA2=0.5m²

Answered: Image /qna-images/answer/7606ef1e-8550-4206-a457-ec2fced2c6ea.jpg

Answered: 3- What is the volumetric flow rate at…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the Reynold’s number for a flow of oil (SG = 0.80, ? = 0.00200 lb-s/ft2) in a 6-in diameter pipe at a flow rate of 10ft3/s. Is the flow laminar or turbulent? thank you!
Water at 100°F is flowing through a straight 4-in schedule 40 pipe at a rate of 1 gal/min. The length of the pipe is 10 ft, find the velocity at the center of the pipe in feet per second?A. 0.0378B. 0.0504C. 0.0454D. 0.0252
What is the ratio of the average velocity to maximum velocity for water flowing in a 1" schedule 40 pipe? Assume laminar flow.A. 0.8B. 0.9C. 0.6D. 0.5
Need detailed solution. During a trip to the beach (Patm = 1 atm = 101.325 kPa), a car runs out of gasoline, and it becomes necessary to siphon gas out of the car of a Good Samaritan. The siphon is a small-diameter hose, and to start the siphon it is necessary to insert one siphon end in the full gas tank, fill the hose with gasoline via suction, and then place the other end in a gas can below the level of the gas tank. The difference in pressure between point 1 (at the free surface of the gasoline in the tank) and point 2 (at the outlet of the tube) causes the liquid to flow from the higher to the lower elevation. Point 2 is located 0.75 m below point 1 in this case, and point 3 is located 2 m above point 1. The siphon diameter is 5 mm, and frictional losses in the siphon are to be disregarded. Determine (a) the minimum time to withdraw 4 L of gasoline from the tank to the can and (b) the pressure at point 3. The density of gasoline is 750 kg/m3. Answer: Δt = 53.1 s, P3 = 81.1 kPa
What is the minimum pipe diameter in cm that can be recommended if the flow is 5 m^3/s and the design velocity if the system is 3 m/s?
HYDRAULICS Benzene flows through a 100 mm diameter pipe at a mean velocity of 3 m/s. Find discharge in liter per second.
the hydraulic radius of a pipe with a diameter of 12mm is
D1 = 20 MM D2 = 10 MM H2 = 5 M V1 = 4 M/S P1 = 4 ATM A.Find the flow velocity and pressure in the bathroom B.What is the Horsepower rating of the motor pump in the inlet pipe needed? Assuming 60% Efficiency
water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir height=220ft length of pipe= 1500ft final aubdivisiion= 24ft, 20psi 1)determine the normal pipe size 2) if the pipe size is not avalible what size combination will work 3) if we used a 8 inch pipe determine the min thickness 4)determine the max pressure that can deelope in the 8in system
The flow rate of a hydraulic fluid with a Sg of 1.08 through a 2-in. I.D. orifice is 50 gal/min. If the pressure drop across the orifice is 5 lbf/in.", what is the discharge coefficient?
A 152.4 mm, Schedule 40 pipe line 91.4 m long conveys 3028 l/min of cold water from a pump to a point of discharge 24.4 m higher than the pump. There are four 90° elbow in the line. Find the pumps dynamic discharge head. Use Table of Equivalent Length of Straight Pipe (see image). Please help. Thank you :)
10.21 Determine the energy loss for a gradual contraction from a DN 125 Schedule 80 steel pipe to a DN 50 Schedule 80 pipe for a flow rate of 500 L/min. The cone angle for the contraction is 105. Answer is. hL=0.224m. Please show steps to get this answer.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

3- What is the volumetric flow rate at point 3 in the following pipe system? a) 3 b) 0.3 0.5 다미 e) 10 5 1 V₁ = 10 m/s A₁ =0.5*² Ag=0.3m² 2 4₁ = 4 m/s Az=0.51²