3. A cut slope consist of soil materials that has a unit weight of 16 KN/cu.m and undrained shear strength 28 KN/sq.m. The slope makes an angle of 50° with the horizontal. Assume a stability number of 0.17. a. Determine the stability factor b. Determine the maximum height to which the cut could be made c. Determine the angle that the failure plane makes with the horizontal if BA=7.6m.

3. A cut slope consist of soil materials that has a unit weight of 16 KN/cu.m and undrained shear strength 28 KN/sq.m. The slope makes an angle of 50° with the horizontal. Assume a stability number of 0.17. a. Determine the stability factor b. Determine the maximum height to which the cut could be made c. Determine the angle that the failure plane makes with the horizontal if BA=7.6m.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.16P

See similar textbooks

Similar questions

3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). a. If H = 5 m, and β = 20°, find the sliding force. b. If H = 5 m, and β = 20°, find the force that resist sliding on the rock surface. c. If HCR = 8 m, find the minimum angle β so that the slope is stable.
Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface.
An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.
Given an infinite slope with the following properties: γ = 17 kN/m3, H = 5 m, β = 34°, φ = 25° and c = 20 kPa. a. Determine the normal stress. b. Determine the shear stress. c. Determine the factor of safety.
Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the maximum depth in meters up to which the cut could be made?
A 9m cut slope is shown in the figure. The unit weight of soil is 17kN/m3. Friction angle and cohesion along the rock surface are 20 degrees and 24kPa respectively. The slope makes an angle of 300 from horizontal and the failure plane is at 150. Determine the developed frictional force on the failure plane.
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the stability factor?
The soil of a infinitely long slope has cohesion of value 20 kPa and dry unit weight of 16 kN/m3. If the slope angle is 40° and has a critical height of 5 m, determine the angle of internal friction of the soil.
An infinite slope in purely cohesive soil has a saturated unit weight of 20 kN/m^3 and effective cohesion of 48 kPa. It has a slope of 18 degree. The clay has a depth of 5m over ledge rock. Depth of clay is measured vertically. 1. Determine the FS against slippage. 2. Determine the critical depth. 3. Compute for the stability number.