A long slope is made with sand having an internal friction angle of 36°. If the slope is submerged completely due to rise in water table, then what should be the maximum slope angle for a factor of safety of 2. The saturated unit weight of sand is 18KN / m3 and the unit weight of water is 10kN/m³.

A long slope is made with sand having an internal friction angle of 36°. If the slope is submerged completely due to rise in water table, then what should be the maximum slope angle for a factor of safety of 2. The saturated unit weight of sand is 18KN / m3 and the unit weight of water is 10kN/m³.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.30P

See similar textbooks

Similar questions

A long slope is made up of a cohesionless soil with the internal friction angle of 34°. If the water table rises to the surface of the slope, then determine the maximum possible value of the slope angle to get a factor of safety of 1.5. Take saturated unit weight as 18 kN/m3 and the unit weight of water as 10 kN/m3.
An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.
The soil of a infinitely long slope has cohesion of value 20 kPa and dry unit weight of 16 kN/m3. If the slope angle is 40° and has a critical height of 5 m, determine the angle of internal friction of the soil.
3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). a. If H = 5 m, and β = 20°, find the sliding force. b. If H = 5 m, and β = 20°, find the force that resist sliding on the rock surface. c. If HCR = 8 m, find the minimum angle β so that the slope is stable.
Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface.
Given an infinite slope with the following properties: γ = 17 kN/m3, H = 5 m, β = 34°, φ = 25° and c = 20 kPa. a. Determine the normal stress. b. Determine the shear stress. c. Determine the factor of safety.
An infinite slope is inclined at 22 degree. A plane of failure has developed at depth of 8 m from the surface. Given dry unit weight = 18kN/m3, c’ = 12kN/m2, angle of friction = 23.5 degree and saturated unit weight = 23kN/m3. Calculate the slope factor of safety if: (i) water table exists far from the slip line
Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the stability factor?
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the maximum depth in meters up to which the cut could be made?
An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, ⍴ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). If HCR = 8 m, find the minimum angle β so that the slope is stable.