3. A hollow steel cylinder with outer radius ro = 60mm and a material thickness t = 5mm is subjected to an unknown torque T. The material has a yield strength oyp = 270 MPa. Using the Von Mises failure theory, determine the maximum allowable value of the torque T in kN-m.

3. A hollow steel cylinder with outer radius ro = 60mm and a material thickness t = 5mm is subjected to an unknown torque T. The material has a yield strength oyp = 270 MPa. Using the Von Mises failure theory, determine the maximum allowable value of the torque T in kN-m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.7P: -7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5...

See similar textbooks

Related questions

Q: A helical compression spring is made of a specialty alloy wire with a wire diameter d = 4 mm and an…

A: Given data: Helical compression spring Diameter, d = 4 mm Inner diameter,…

Q: Q.3) A W8 X 24 steel column of 7-ft effective length supports an eccentric load as shown below. The…

A: Given Data:- W 8×24 steel column Effective length le=7 feet…

Q: A steel [E = 200 GPa] rod with a circular cross section is 7.5-m long. Determine the minimum…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 4500 N…

A: The Point A will be subjected to tensile stress due to bending stress generated by force F.bending…

Q: QF8: The 0.06R (mm)-diameter bar is made of a brittle material with the ultimate strengths of 0.1SR…

A: Given: The diameter of bar, d = 0.06R The ultimate strength of bar = 0.15R MPa (T) and 0.25R (C)

Q: he bar shown made from steel (Sut = 130 ksi) is subjected to a fully reversed bending moment of…

A: Endurance limit The fatigue or endurance limit of a material is defined as the maximum amplitude of…

Q: 5 (a) A steel bar is subjected to a sequence of completely reversed stress cycles which vary over a…

A: Given , Endurance Limit(Se) = 430 N/mm2 Completely reversed stress cycle, S1 = 570 N/mm2 S2 = 630…

Q: Determine the number of life cycles for an alternating stress of 70 ksi. Select one: a. N = 1.66E+05…

Q: A cube of a material with a yield strength of 100x10° N/m*is subjectedtotheloads shown onthe right.…

Q: a) The material is 2024-T4 aluminum with a yield strength of 47 ksi b) The rod length L=6 in and arm…

Q: the height (in mm) of cross section from strength calculation h = ?

A: working stress = yeild stress/ factor of safety = 220/1.6 = 137.5 MPa

Q: The assembly shown consists of an aluminum shell (E, = 70 GPa, az= 23.6 × 10-6C) fully bonded to a…

Q: A thin-walled cylinder of diameter 40 mm is subjected to an internal pressure of 5 N/mm² and a…

Q: Q2/ 7 A steel bolt 0.005 m² in cross-section is subjected to a Static mean load of 200 KN. What…

A: To find : The value of completely reversed direct fatigue load . Given data : The Area is A=0.005…

Q: A mild steel shaft of 40 mm diameter is subjected to a bending moment of 115 N-m and torque, T. If…

Q: A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and…

Q: A 1m long steel bar (E=200GPa) of 10mmx10mm dimension fixed at both ends is heated to 90°C from…

Q: 2. A solid steel rod with a diameter of d = 50mm is subjected to a bending moment M = 1.5 kN-m and a…

Q: he bar shown in the following figure has a diameter of 20 mm and is subjected to a force P = 2750 N…

A: Given:d=20 mmP=2750 NF=14000 NSyt=480 MPaPoint A will be subjectd to tensile stress due to bending…

Q: A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Neglecting the weight of the…

Q: 5. A platform is suspended by two parallel rods, as shown in the sketch, with each rod being 1.28 cm…

Q: A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress…

Q: 2. A solid circular steel rod with a radius of r = 50mm is subjected to an axial compressive load P…

Q: A closed cylindrical vessel contains a fluid pressure of P (Mpa). The cylinder has an inside…

Q: Q3 - The homogeneous bar AB have diameters 190mm when subjected to an axial tensile load of 34KN.…

Q: The principal stresses at a point inside a solid object are ơ1 = 100 MPa, 02= 100 MPa and 03= 0 MPa.…

Q: The part shown is loaded at point C with 290 N in the positive x direction and at point E with 200 N…

A: .

Q: B. 5 m 3 m 30 mm -20 mm T20 mm The assembly above includes pin-connected column AB. Suppose that an…

Q: Consider the steel arm assembly in the figure below that supports load R. Using the Coulomb-Mohr…

A: For solution refer below images.

Q: QUESTION 1 A punch shown in Figure 1 is used to make a hole in a metal plate with thickness h3. The…

Q: The rigid bar ABC is supported by pin at A and aluminium wire BD, is horizontal before the Load P is…

Q: B/A cylindrical piece of carbon-steel with dimension of 100 mm length and 10 mm diameter exposed to…

Q: Determine factors of safety, based upon the distortion energy theory, for stress elements at A and B…

Q: A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000N. If the…

Q: A brittle material made of ASTM grade 30 cast iron has ultimate strength in tension of 31 kpsi and…

A: given data- Ultimate strength in tension- 31 kpsi Ultimate strength in compression- 109 kpsi σx=20…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 3500 N…

Q: 2. The tapered cylindrical bar in Fig. 2 is subjected to opposing torques T on its free ends. For…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Given:F=500 NP=1500 Nd=40 mmSyt=60MPaI=π64*404 =125663.70 mmStresses acting at point A:The Force…

Q: In the system shown, when a compression load P is applied to the rod, what is the bearing stress…

Q: A thin-walled column has a circular cross section of diameter 200 mm and thickness 5 mm. It carries…

Q: The bar shown made from steel (S= 90 ksi) is subjected to a fully reversed bending mornent of 1500…

A: Given data:

Q: A rod of diameter 30 mm is to sustain an axial compressive load of 20 kN and twisting moment of 1.5…

Q: Problem 3 An alloy bar 6m long is held between two supports by a steel rod 25 mm diameter passing…

Question

Please full solution. Big and clear Handwriting. Thank you

3. A hollow steel cylinder with outer radius r. = 60mm and a material thickness t = 5mm is subjected to
an unknown torque T. The material has a yield strength oyp = 270 MPa. Using the Von Mises failure
theory, determine the maximum allowable value of the torque T in kN-m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A copper tube with circular cross section has length L = 1.25 m, thickness t = 2 mm, and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 300 N·m torque acting at the ends. If the allowable shear stress is 25 MPa and the allowable angle of twist between the ends is 2.5°, what is the minimum required outer diameter d?
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses in tension, compression, and shear arc 90 MPa, 70 MPa, and 40 MPa, respectively. Also, the allowable tensile strain is 220 x 10-6, Determine the minimum required diameter d of the bar, If the bar diameter d = 40 mm, what is Tmax?
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
A solid circular steel cylinder S is encased in a hollow circular aluminum tube A. The cylinder and tube are compressed between the rigid plates of a testing machine which applies forces P. Calculate the allowable value of the compressive force if the yield stresses of sleel and aluminum are srs = 50 Ksi and ??A= 60 ksi, respectively. Assume that As= 12 in2. AA= 6 in2. L = 20 in., Es= 29,000 tsi and EA=10,600 ksi
A large spherical tank (see figure) contains gas at a pressure of 420 psi. The tank is 45 ft in diameter and is constructed of high-strength steel having a yield stress in tension of 80 ksi. (a) Determine the required thickness (to the nearest 1/4 inch) of the wall of the tank if a factor of safety of 3,5 with respect to yielding is required. (b) If the tank wall thickness is 2.25 in., what is the maximum permissible internal pressure?