3. A piston-cylinder contains ideal CO (carbon monoxide, M=28.01 Ib/lbmol) that undergoes a process PV14=constant. The initial temperature is 300•F and the gage pressure is 35.3 psig. The final volume is twice the volume at state 1. The mass is 1 lb. Find the pressure and temperature at state 2 and the work and heat transfer. The value of universal gas constant is 1545 ft.lIbf/lbmol.•R. Ignore kinetic and potential effects.

3. A piston-cylinder contains ideal CO (carbon monoxide, M=28.01 Ib/lbmol) that undergoes a process PV14=constant. The initial temperature is 300•F and the gage pressure is 35.3 psig. The final volume is twice the volume at state 1. The mass is 1 lb. Find the pressure and temperature at state 2 and the work and heat transfer. The value of universal gas constant is 1545 ft.lIbf/lbmol.•R. Ignore kinetic and potential effects.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 30RQ: A gas is compressed inside a compressor's cylinder. When the piston is at its bottom dead center,...

See similar textbooks

Similar questions

Two vessels A and B of different sizes are connected by a pipe with a valve. Vessel A contains 134L of air at 2,639.66 kPa, 87.38°C. Vessel B, of unknown volume, contains air at 69.36 kPa, 6.33°C. The valve is opened and, when the properties have been determined, it is found that Pm = 1,041.50 kPa, tm = 46.30°C. What is the volume of vessel B?
A rigid, well-insulated tank contains air. A partition in the tank separates 12 ft^3 of air at 14.7 lbf/in2, 40◦F (left side of the tank) from 10 ft^3 of air at 50 lbf/in2, 200◦F(right side of the tank), as illustrated in the figure. The partition is removed and air from the two sides mix until a final equilibrium state is attained. The air can be modeled as an ideal gas, and kinetic and potential energy effects can be neglected. (Note: values for the left side of the tank are denoted with a subscript L, and values for the right side of the tank are denoted with a subscript R). a) Determine the final temperature (in F) b) Determine the final pressure (in lbf/in^2) c) Calculate the amount of entropy produced, in Btu/R d) Is this mixing process reversible or irreversible?
Carbon Dioxide is contained in a piston-cylinder assembly and undergoes a cycle made of the fol- lowing processes: • Process 1-2: Constant volume from 1 bar, 300 K to 600 K • Process 2–3: Polytropic expansion with n=k until P3 = P1 • Process 3-1: Isobaric compression (a) Sketch the cycle on p-v and T-v coordinates (b) Determine the work and heat transfer in each process, in kJ/kg (c) Determine the type of cycle that this is. If it is a power cycle, compute the thermal efficiency. Otherwise, compute the coefficient of performance for a heat pump cycle.
104#1. an ideal gas with R=0.062 BTU/lbm-degree R and Cv=0.158 BTU/lbm-degree R undergoes athree process cycle in a cklose system. from the initial state of 20 psia and 570degree R, the gas is compressed at coinstant pressure to 1/5 of its initial volume, process 1-2; it is then heated isochrocally to state 3, process 2-3; and finally, it expands polytopically with index n=1.5 back to its initial state, process 3-1. determine the pressure, specific volumes and temperatures at cardinal points around the cycle and the cycle thermal efficiency.
A frictionless piston-cylinder assembly initially contains B m3 of air at A kPa pressure. In this state, a linear spring touches the piston but does not exert any force. Then the air is heated and the piston moves up. Finally, the volume is C m3 and the pressure is D kPa.a) Draw the state change PV diagram,b) Calculate the total work done by the air (kJ), c) Calculate the work done against the spring (kj).
Thermodynamics subject. Pleas show the complete and step by step solution. . A certain gas at 101.325kPa and 160C whose volume is 2.83m3 are compressed into a storage vessel of 0.31m3 capacity. Before admission, the storage vessel contained the gas at 137.8kPa and 240 C; after admission the pressure has increased to 1171.8kPa. What should be the final temperature of the gas in the vessel in Rankine?
Between 1-2: Isothermal compression (1st process)Between 2-3: Isometric compression (2nd process)Between 3-1: Adiabatic expansion (3rd process) A cyclic process through which N2 gas, which is considered to be the ideal behaving, is treated, has been described above. In case 1, the volume of gas is 9.6 m3, pressure 200 kPa. Since the pressure in state 3 is 750 kPa, find the work done in the whole process in kJ. Draw the P-V diagram for the cycle.
Given: P3 = 4 kPa, x3 = 0.6 , P4 = 4 kPa, T1 = 25 oC, T2 = 35 oC, mdot_steam = 25 kg/s. Find mdot_water (kg/s).mdot_water = _________ kg/s.
An oxygen gas R = 0.2598 KJ/kg°k and k = 1.395. If 4 kg of oxygen undergo a reversible non flow constant pressure process from initial volume =1.2 cubic meter and initial pressure = 690 kPa to a state where final temperature = 600°C. What is the initial temperature ? Determine the constant volume specific heat. need a complete solution, symbol, and cancellation:)
Air is compressed in a piston–cylinder assembly from p1 = 25 lbf/in2, T1 = 500°R, V1 = 9 ft3 to a final volume of V2 = 1 ft3 in a process described by p⁢v1.30=constant. Assume ideal gas behavior and neglect kinetic and potential energy effects. Using constant specific heats evaluated at T1, determine the work and the heat transfer, in Btu.
A gas cylinder with interior volume 11.6 L holds compressed air at 17.4 MPa. The cylinder is joined by a hose of negligible volume to a second cylinder that’s been pumped down to vacuum. When the valve on the full cylinder is opened, the air expands to fill the entire system, all the while maintaining a constant temperature. If the energy that becomes unavailable to do work is 171.8 kJ, what’s the volume of the second cylinder (L)?
A Piston-Cylinder arrangement initially contains 3 kg of water as saturated liquid at 200 kPa pressure. Then, heat transfer to water, some of the water evaporates and the piston rises. When the volume is 60 liters, the piston touches the stoppers. Heating process continues until the pressure is twice the initial pressure. Plot the state change on the P-v diagram showing the saturation curves. Also, A) Finally, find the mass of the system in liquid phase. B) Find the final temperature. C) Calculate the total work done and heat transfer during the process.