3. Consider the floor plan shown. a. Compute the tributary areas for (a) floor beam B3, (b) floor beam B4, (c) girder G3, (d) girder G4, (e) corner column C3, and (f) interior column C4 b. Assuming a uniform live load of 60 psf, determine the live loading for the (a) floor beam B3, (b) floor beam B4, (c) girder G3, (d) girder G4, (e) corner column C3, and (f) interior column C4. Consider the live load reduction if permitted by the ASCE/NSCP Standard

3. Consider the floor plan shown. a. Compute the tributary areas for (a) floor beam B3, (b) floor beam B4, (c) girder G3, (d) girder G4, (e) corner column C3, and (f) interior column C4 b. Assuming a uniform live load of 60 psf, determine the live loading for the (a) floor beam B3, (b) floor beam B4, (c) girder G3, (d) girder G4, (e) corner column C3, and (f) interior column C4. Consider the live load reduction if permitted by the ASCE/NSCP Standard

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A closed rectangular tank measuring 4 m long, 8.89m wide, and 3m high is filled to a depth of 1.8m with oil (SG=0.8). The tank is attached to a truck that is traveling horizontally at 9.81m/s^2. Determine the allowable force (kN)at the rear wall of the tank.
The bin is 1.5 m wide and is filled with water to the level shown. Determine the resultant force on the side AB and on the bottom BC.
Answer the following: a. hydrostatic force acting on a wall b. weight of dam if the unit weight of concrete is 23.54 kn/cum c. overturning moment d. location of the resultant measured from the toe of the dam
A slab shown supports the load W1 and W2 for every one-meter strip along the longitudinal section. If the total length L= 15m and W=145 kN/m, determine the load W2 in kN/m so that the upward pressure on the slab is uniform and that the barge remains horizontal
A vertical triangular gate 1.2 high have its 2m base flushed with water surface. Determine the location of the center of pressure from the top.
A vertical triangular gate having a height “h” and a base “b” issubmerged in water. Identify the following: 1. Depth of center of pressure with its vertex at the liquid surface.2. If the vertex is 1 meter below the surface, determine the locationof center of pressure from the surface if b = 4 m and d = 3 m,and3. determine its hydrostatic pressure on one side of the gate.
Find the load combination for (dead load = 25 kN, live load = 10 kN, wind load = 5 kN).
A concrete wall is 1.2 meters high and 0.203 meters thick. Concrete has a specific gravity of 23,7 kN/m3 In connection with heavy rain, water fills between the wall and the ground. The height of the water is h . The wall rests on the ground without any form of anchoring. A)Calculate the maximum height,h , that the rainwater can reach before the wall topples B)Calculate how thick the wall must be so that it does not topple over if h= 1,2m
b) There is a control room underneath the storage reservoir which covers the same area as the reservoir itself. Calculate the total water load on the roof of the control room at maximum allowable depth. c) Suggest a method of supporting the roof of the control room
Water flows at the rate of 0.015 m3/s through a 100 mm diameter orifice used in a 200 mm pipe. What is the difference of pressure head between the upstream section and the vena contracta section? Take co-efficient of contraction Cc = 0.60 and Cv = 1.0.
The steel framework is used to support the 100-mm reinforced stone concrete slab that carries a uniform live loading of 24 kPa. Sketch the loading that acts along members BE and FED assuming simple supports. Set b = 3.6 m and a = 1.2 m. Use alternate method for live load reduction. Solve in accordance to NSCP 2015.
A gate slanted 60 degrees from the horizontal with width = 1.6 m and height = 2.4 m is submerged by a depth of 1.8 m, determine the pressure at the top of the gate in Pa. Use whole number.