3. For the canal gate shown, sketch the pressure distributions applied to it. Sketch the resultant force on the gate? If h1 = 6.0 m and h2 = 4.0 m, sketch the pressure distribution to the gate. Also, what is the value of the resultant force on the gate and at what height above the bottom of the gate is it applied 777 h₂

3. For the canal gate shown, sketch the pressure distributions applied to it. Sketch the resultant force on the gate? If h1 = 6.0 m and h2 = 4.0 m, sketch the pressure distribution to the gate. Also, what is the value of the resultant force on the gate and at what height above the bottom of the gate is it applied 777 h₂

Name: 3. For the canal gate shown, sketch the pressure distributions applie
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3. For the canal gate shown, sketch the pressure distributions applied to it. Sketch the resultant force onthe gate? If h1 = 6.0 m and h2 = 4.0 m, sketch the pressure distribution to the gate. Also, what is the valueof the resultant force on the gat

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.129RP

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
Determine the resultant force acting on the elbow of the thin-walled pipe when the pipe carries a uniform internal pressure p0.
Each of the three gates has a constant width 1: (perpendicular to the paper). Calculate the force P required to maintain each gate in the position shown. Express your answers in terms of b, c, h, and (the weight density of the fluid).
Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels are 16 ft on the upstream side and zero on the downstream side. For water, use =62.4lb/ft3.
The distance between the two plates, which are 2 m x 2 m in size and parallel to the earth surface, is 9 mm, and there is water at 20 ° C between them. Find the force in (N) to be applied to pull the top plate to the right at 10 m / s.
A swimming pool has a width of 4 m and a side profile as shown. Determine the resultant force.Determine the magnitude that the water exerts on walls AB and DC, and on the bottom BC, using the general solution. Determine also its direction and location.DRAW PRESSURE DIAGRAM
Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm. If the intervening passages are filled with oil and a force of PB=4.6kn is acting on B. What must be the pressure in N/m2 exerted at A?
Determine the buoyant force on a 800 ft3 balloon at an altitude of 500 ft. Give the direction of this force.
Calculate the resultant force that the oil exerts on plate B Determine the location of FR measured from the bottom of the tank. (see image)
Find the force P required to hold the gate in the position as shown in the figure. The gate is 5 meters wide.
A dam is used to store water, and a rectangular gate which is hinged at its bottom edge is used to control the flow as shown in figure 1. For this gate, width = 1 m (in the direction of the page) , α = 65°, h1 = 1 m, and h2 = 5 m. Figure 1: Schematic for task 1. (Giancoli et al.) a. Describe the forces acting on the gate and the center of pressure. b. Determine the resultant force and the position of the center of pressure on the gate. c. What is the maximum gate mass that is needed for it not to fall? d. Show yc, yR, hc, hR, FR, and W on the free body diagram.
When calculating the value of the force exerted by the water on the window of the dam. Explain why if the pressure varies from the surface of the water, the lower limit for the integral is taken from depth "a" and not from zero? (it is convenient that you make diagrams to support your answer).