1) Determine the x and y components of force at pin A. Express your answers in kilonewtons to three significant figures separated by a comma. 2) Determine the x and y components of force at pin D. Express your answers in kilonewtons to three significant figures. Enter your answers separated by a comma.

1) Determine the x and y components of force at pin A. Express your answers in kilonewtons to three significant figures separated by a comma. 2) Determine the x and y components of force at pin D. Express your answers in kilonewtons to three significant figures. Enter your answers separated by a comma.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.21P: Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10...

See similar textbooks

Similar questions

Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Compute the magnitudes of all forces acting on member CDE of the frame. answer: Pbc= 10.0 kips, Pbd= 20.0 kips, E= 19.70 kips
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
Two gondolas on a ski lift are locked in the postion show in the figure while repairs are being made elsewhere.The distance between support towers is L = LOO ft.The length of each cable segement under gondolas weighing WB= 450 lb and Wc=650 lb are DAB=12 ft, DBC=70 a , and DCB=20 ft . The cable sag at B is AB = 3.9 ft and that C is A = 7.1 ft.THe effective cross-sectional area of the cables is Ae=0.12 in". (a) Find the tension force in each segment; neglect the mass of the cable. (b) Find the average stress(σ) in each cable segment.
Figure Q3 shows a steel bar of diameter 16 mm and length 600 mm subjected to axial forces.If E = 210×103 N/mm2for steel, determine the change in its length.
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
A uniform bar 6 m long is held by ropes at the ends making angle 60° and 30°, respectively, with the horizontal. A weight of 400 N is hung 1.0 m from the left end where the 60° rope is attached. Find the tension in the rope and the weight of the bar.