3. In a large field with a flat surface, an excavation will take place. According to the drilling works, no groundwater was encountered, and a homogeneous cohesionless soil has been found throughout the excavation depth. As a result of the experiments, the internal friction angle of the relevant soil was found to be 24°, and the dry and saturated unit weights were 17 kN/m³ and 19.2 kN/m³, respectively. According to the information given, what is the inclination of the steepest slope that can be excavated in the area?

3. In a large field with a flat surface, an excavation will take place. According to the drilling works, no groundwater was encountered, and a homogeneous cohesionless soil has been found throughout the excavation depth. As a result of the experiments, the internal friction angle of the relevant soil was found to be 24°, and the dry and saturated unit weights were 17 kN/m³ and 19.2 kN/m³, respectively. According to the information given, what is the inclination of the steepest slope that can be excavated in the area?

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter17: Subsoil Exploration

Section: Chapter Questions

Problem 17.12P

See similar textbooks

Similar questions

A soil excavation was done until 4m below the surface of the soil. It was identified that the shallow ground water level is 2m below the ground level and the upper is dry. The properties of the soil are: Gs = 2.7, e = 0.50, and ϕ’ = 30degrees. Assuming no seepage. What is the value of the in-situ soil’s unit weight above G.W.T. in kN/m3? What is the maximum neutral stress at the deepest point of excavation in kPa? What is the value of the total stress of soil at the surface of the ground water table in kPa? What is the value of the effective stress at the deepest point of excavation in kPa?
For the first series of tests, no drainage of pore water occurs, either when the normal load is applied or during shearing (relating to clay’s very low coefficient of permeability). How does the “no drainage” control can be visualized?
Define Normalized Load vs. Displacement Behavior of Drilled Shafts in Granular Soils (from Rollins eta!. 1994).
Subject: Soil Mechanics Please prove a solution and diagram A 2.5 cm thick sample of clay was taken from the field for predicting the time of settlement for a proposed building which exerts a uniform pressure of 100 kN/m2 over the clay stratum. The sample was loaded to 100 kN/m2 and proper drainage was allowed from top and bottom. It was seen that 50 percent of the total settlement occurred in 3 minutes. Find the time in days required for 50 percent of the total settlement of the building, if it is to be constructed on a 6 m thick layer of clay which extends from the ground surface and is underlain by sand a. 120 b. 140 c. 130 d. 110
An exploratory drill hole was made in a stiff saturated clay having a moisture content of 29% and Gs = 2.68 (Figure 9.27). The sand layer underlying the clay was observed to be under artesian pressure. Water in the drill hole rose to a height of 6 m above the top of the sand layer. If an open excavation is to be made in the clay, determine the safe depth of excavation before the bottom heaves.
The figure below shows a proposed site where an excavation will be made. The 12 ft layer of sand will be removed, so that the top of the 30 ft normally consolidated clay layer will be exposed (Assume that changes in GWT do not affect γt of clay). a. Assume that the water-table location remains the same during excavation. Compute the σ, σ′v, and u values at the middle of the clay layer before and after the excavation b. Assuming 1-D conditions, compute how much the clay layer will deform due to this excavation, in inches. Specify whether this is settlement or heave
An exploratory drill hole was made in a stiff saturated clay, as shown in Figure 1, having a moisture content of 25% and Gs = 2.56. The sand layer underlying the clay was observed to be under artesian pressure. Water in the drill hole rose to a height of 3 m above the top of sand layer. If an open excavation is to be made in the clay. a.What is the maximum depth of excavation before the bottom heaves? b.What would be the required height of water inside the cut in order to ensure a factor of safety of 1.5?
An exploratory drill hole was made in a stiff saturated clay having a moisture content of 38.9% and Gs = 2.34 as shown in the figure. The sand layer underlying the clay was observed to be under artesian pressure. Water in the drill hole rose to a height of 13.8 ft above the top of sand layer. If an open excavation is to be made in the clay, determine the (a) unit weight of the clay, and the (b) maximum cut before the bottom heaves.
1 In order to restore a river embankment damaged by an earthquake, a soil of 50,000 m3 estimated after compaction was needed. From the laboratory tests of soil from the excavation site, the water content was w = 15%, and the void ratio was e = 0.60, and the specific gravity of soil was Gs =2.70. The soil was carried by truck to the construction site. The load capacity of the truck is 6.5 t. The construction of embankment was done by compacting after adding water so that the water content becomes 20%. The dry density of soil after compaction was 1.80 t/m3 . Answer the following questions. The density of water is 1.0 t/m3 . find the saturation Sr, the bulk density, and the dry density of soil at the excavation site. Find the total number of trucks needed for the construction. Find the total volume of soil excavated at the excavation site. Find the total volume of water added to obtain the prescribed water content. Assume that evaporation of water is negligible. The embankment is needed…
plz, solve what you have been asked in this problem, plz, solve all the parts of the problem? Geotechnical Engineering-2 1. In a consolidated drained triaxial test, a specimen of saturated sand failed under an deviator stress of 250 kN/m2, when the cell pressure was 100 kN/m2 i)Solve for the shear stress on the failure plane and maximum shear stress at failure? ii)Solve for factor of safety with respect to shear strength on the plane of maximum shear stress? ii) Illustrate by drawing the Mohr circle for the failure stress condition. iv)Solve for ɸ′ and the theoretical inclination of the failure plane to the horizontal.
A saturated clay encountered in a deep excavation is found to have a water content of 23.5%. Determine its porosity and (saturated) unit weight.
An excavation is to be performed in a stratum of clay, 9 m thick, underlain by a bed of sand. In a trial borehole, the ground-water is observed to rise up to an elevation 3 m below ground surface. Find the depth ofwhich the excavation can be safely carried out without the bottom becoming unstable under uplift pressureof ground-water. The specific gravity of clay particles is 2.70 and the void ratio is 0.70. If the excavation is tobe safely carried to a depth of 7 m, how much should the water table be lowered in the vicinity of the trench?