Analyze and identify data given on the following problems and employ related equations to determine the corresponding required data for each problem. 3. In the circuit shown below, the external resistance connected across the terminals of the battery is1.44 Ohms. Determine the current, power lost in battery, load power and efficiency of the system.++12 V12 V12 V0.30Ω12 V12 VR = 1.4420.3020.3020.3020.3024. Five batteries connected in parallel, each having an emf of 12 volts and resistances of 0.30, 0.42,0.32, 0.36, 0.41 Ohm. A resistance of 0.80-Ohm is connected across the terminals of the battery.Determine: (a) current; (b) terminal voltage; (c) current in each cell; (d) Efficiency of the system.12 V12 V0.32212 V12 V12 VR = 0.8020.30 Ω0.4220.3620.412

In this question, 4 parallel cells are connected to a external load. Which is shown in the…

3. In the circuit shown below, the external resistance connected across the terminals of the battery is 1.44 Ohms. Determine the current, power lost in battery, load power and efficiency of the system. + + 12 V 12 V 12 V 12 V 12 V R = 1.442 0.302 0.302 0.302 0.30 Ω 0.30 Ω

3. In the circuit shown below, the external resistance connected across the terminals of the battery is 1.44 Ohms. Determine the current, power lost in battery, load power and efficiency of the system. + + 12 V 12 V 12 V 12 V 12 V R = 1.442 0.302 0.302 0.302 0.30 Ω 0.30 Ω

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The percent values of the voltage, current, impedance, and volt-amperes for a givenpower system are 90, 30, 80, and 150 percent, respectively. The base current and baseimpedance are 60A and 40Ω, respectively. Calculate the actual values of the voltage,current, impedance, and volt-amperes.
A room air conditioner has a coefficient of performance of 2.9 on a hot day and uses 850 W of electrical power. (a) How many joules of heat does the air conditioner remove from the room in one minute? (b) How many joules of heat does the air conditioner deliver to the hot outside air in one minute? (c) Explain why your answers to parts (a) and (b) are not the same.
(a) Is a wattmeter required to measure the real power delivered to a resistive load? (b) A wattmeter will indicate zero when the current lags (or leads) the voltage by 90 0 . (c) An incandescent lamp, rated at 100 W, gives a certain amount of light when placed across the 120 V ac power line. Would the amount of light increase, decrease or remain the same, when the lamp is placed across a 120 V dc power line? Explain your answer.
Determine ?1,?2,?1 and ?2. Find the power dissipated in the 10-ohm resistor.
a hydroelectric plant has a turbine and generator with an efficiency of 90%. if the dam has a head of 10 feet and the water flows at 300 feet cube per second, calculate the power generated. and explain the service drops in power systems?
A power plant produces 1000MW to supply a city 40km away. Current flows from the power plant on a single wire with resistance through the city and returns via the ground, with negligible resistance. At the power plant the voltage between wire and ground is 115 kV. Determine: (a) the current in the wire, and (b) the fraction of the power lost in transmission.
Please explain in detail and show all the solution if there are. Data Gathered during the Experiment Thevenin Voltage (VTH) = 1.618 volts Thevenin Resistance (RTH) = 1211 Ω Load Resistance Load Voltage Dissipated Power 7600Ω 1.511 0.0002 2000Ω 0.915 0.0004 900Ω 0.30 0.0003 1. Analyze the data for a pattern. What is the highest dissipated power in the list? When does this occur? 2. What value of Load Resistance develops a voltage drop across it closest to the value of VTH? 3. What value of Load Resistance draws the largest current from VTH? Please explain how the you arrived in that conclusion.
Voltage Drop! Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C. what is the Voltage Drop ? Answer?
complete solution. Fix yourcalculator in four decimal places and show your final answers in FOUR DECIMAL places. 1. The resistance of the wire used for telephone is 35 Ω per kilometre when the weight of the wire is 5 kg per kilometre. If the specific resistance of the material is 1.95 x 10^-8 Ω-m, what is the cross sectional area of the wire? What will be the resistance of a loop to a subscriber 8 km from the exchange if wire of the same material but weighing 20 kg per kilometre is used?
A copper conductor wire with a total length of 100ft is used in a 15 amp common household circuit has a resistance of 1.62 ohms/1000ft. If the circuit is fully loaded, determine the heat produced by the conductor? (Hint 1W = 3.413Btu/hr) a. 124.40 Btu/hr b. 99.83 Btu/hr c. 8.29 Btu/hr d. 177.50 Btu/hr
write only the option The electrical power is delivered to the users through five distribution levels. True or False? A.True B.False The average supply restoration for voltage level 11 kV is A.more than 4 hours B.between 1 and 4 hours C.less than 4 hours Tariff is the rate of charging for electrical energy supplied by the utility company to its consumer. Tariff is depends on various factors excpet: A.Type of facilities B.Type of services C.Type of consumers D.Total fixed running annual charges of the utility company Under primary distribution netwrok system, the electrical power is delivered to the users through _________ distribution levels. A.3 B.5 C.2 D.4
A copper transmission line is to be replaced by one of aluminum having the same total resistance. If the cross sectional area of the copper wire is 0.005m2 , what would be the cross sectional area of the new aluminum wire? Note: DRAW THE DIAGRAM